Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Additional safety rules for rotary tools
a. Always wear eye protection when using this tool!
b. If accessory jams, turn tool off before freeing
accessory from the jam.
c. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
"live" wire will make exposed metal parts of the tool "live"
and shock the operator.
d. When using cutoff wheels always have the work
securely clamped. Never attempt to hold the work with
one hand while using any cutting accessory.
e. Keep hands away from rotating accessories.
f. Allow accessories and collets to cool before touching
with bare hands. They will be hot after using.
g. Insure there are no foreign objects in the workpiece
such as nails which if hit could cause loss of control
of unit.
h. Always feed the cutter into the material in the same
direction as the chips are being thrown. Feeding the
tool in the wrong direction can cause loss of control.
i. Keep handles dry, clean, free from oil and grease. This
will enable better control of the tool.
j. When cutting wood, extra care should be taken to
avoid inhalation and minimize skin contact.
k. Wear ear protection. Noise level may be amplified when
using tool in enclosed spaces.
l. This tool has an internal speed control, never use an
external speed control on this unit.
m. Do not use worn accessories.
n. Do not use grinding wheels that have cracks.
o. When turning tool on, hold it away from your face,
since a damaged accessory could come apart.
Additional safety information
Warning! Never modify the power tool or any part of it.
Damage or personal injury could result.
Warning! ALWAYS use safety glasses. Everyday eyeglasses
are NOT safety glasses. Also use face or dust mask if cutting
operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
Warning! Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm. Some examples of
these chemicals are:
lead from lead-based paints,
u
crystalline silica from bricks and cement and other
u
masonry products, and
arsenic and chromium from chemically-treated lumber.
u
Your risk from these exposures varies, depending on how
often you do this type of work.
8
(Original instructions)
To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment,
such as those dust masks that are specially designed to filter
out microscopic particles.
Wear protective clothing and wash exposed areas
u
with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption
of harmful chemicals. Direct particles away from face and
body.
Use the appropriate dust extractor vacuum to remove
u
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to
the operator and those in close proximity.
Use clamps or other practical ways to secure and
u
support the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may
lead to loss of control and injury.
Air vents often cover moving parts and should be
u
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
Caution: When not in use, place tool on its side on a
stable surface where it will not cause a tripping or falling
hazard. Some tools with large battery packs will stand upright
on the battery pack but may be easily knocked over.
Safety of others
This tool is not intended for use by persons (including
u
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
u
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Publicidad
