Publicidad
Idiomas disponibles
Idiomas disponibles
4. Install a new dust collection bag by
EN
inserting the bag handle into the card
slot.
5. Install back the dust-removal hub cover.
Fig. E-14-Fig. E-18
Note: It is recommended to replace the
dust collection bag every two months. If the
dust collection bag reaches capacity, the
indicator blinks orange.
Replacing the Battery Pack
The vacuum contains a removable
rechargeable lithium-ion battery pack
which has a limited number of recharge
cycles. After extended use, the battery
pack may no longer hold a charge. If this
happens, it means the battery pack has
reached the end of its life cycle and needs
to be replaced.
1. Press down the battery pack release
button and slide the battery pack to the
right, as illustrated, to remove it.
2. Install the new battery pack.
Fig. E-19
Cleaning the Multi-Surface
Brush
1. Turn the lock counterclockwise until it
stops, then remove the roller from the
roller brush.
2. Use scissors to cut off the hairs and
fibers that get stuck on the brush roller.
Wipe the dust from the notch and
transparent cover with a dry cloth or
paper towel. Thoroughly dry before
use.
3. When it is dirty, rinse the brush roller
with clean water until it is clean.
4. Stand the brush roller upright for at
least 24 hours until it is fully dry.
Fig. E-20-Fig. E-23
9
Cleaning the Soft Roller Brush
1. As shown in the picture, press the
brush roller release button to remove
the roller from the slot.
2. Use scissors to cut off the hairs and
fibers that get stuck on the brush roller.
Wipe the dust from the notch and
transparent cover with a dry cloth or
paper towel. Thoroughly dry before
use.
3. When it is dirty, rinse the brush roller
with clean water until it is clean.
4. Stand the brush roller upright for at
least 24 hours until it is fully dry.
Fig. E-24-Fig. E-27
Cleaning the Motorized Mini-
Brush
1. Use a coin as illustrated to rotate the
lock counterclockwise until you hear a
click.
2. After unlocking the motorized mini-brush,
remove the brush roller, then rinse and
clean it.
3. Stand the brush roller upright in a well-
ventilated area for at least 24 hours until
it is fully dry.
4. Once the brush roller is dry, reinstall it
by following the disassembly steps in
reverse.
Fig. E-28-Fig. E-31
FAQ
If the vacuum is not working properly, please refer to the table below.
Errors
Possible Causes
The appliance is out of battery or
its battery level is low.
Overheat protection mode
Vacuum does not work.
triggered by a blockage.
The suction opening or air duct is
blocked.
The dust cup is full and/or filter
assembly is clogged.
Weak suction force.
An attachment is blocked.
The motor makes a strange
Main suction opening or
noise.
extension rod is blocked.
The battery indicator is
solid red when charging
Battery pack is damaged.
the vacuum.
The battery indicator blinks
The motor temperature is too
red after turning on the
high. / The bush roller is blocked.
vacuum.
/ The air duct is blocked.
The vacuum is not properly
placed on the dust-removal hub.
The battery indicator
The battery is charged and
does not light up when
switches to Sleep Mode
charging.
automatically.
The problem persists after ruling
out the above two possibilities.
The battery temperature is too
Charging too slow.
low or too high.
LED lights of the multi-
surface brush and
LED lights are damaged.
motorized mini-brush do
not work.
The dust collection bag is
The dust collection status
uninstalled or inappropriately
indicator is solid orange.
installed.
The dust collection status
The dust collection bag reaches
indicator is blinking
capacity or the air duct is
orange.
blocked.
EN
Solutions
Fully charge the vacuum, then resume
use.
Clean the suction opening or air duct.
Wait until the vacuum cools down,
then reactivate it.
Clear any blockage from the suction
opening or air duct.
Empty the dust cup and/or clean the
filter assembly.
Clear any blockage in the attachment.
Clear any blockage in the main suction
opening or extension rod.
Please contact after-sales service for
maintenance.
Check these parts in turn.
Make sure that the charging contacts
of the vacuum is aligned with that of
the dust-removal hub.
The vacuum runs normally.
Please contact the after-sales
department for maintenance.
Wait until the battery temperature
returns normal, and then recharge.
Please contact the after-sales
department for maintenance.
Before dust collecting starts, confirm
that the dust collection bag has been
installed or installed in place.
Replace a new dust collection bag
or clean the air duct. Then press and
hold the dust collection button for 3s
to troubleshoot the problem.
10
Publicidad
