Material Feed - Intimus 45 SC2 Instrucciones De Uso

GB
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
CONTROLS: CONTROLS:
7 = Control display (Fig. 1) 7 = Control display (Fig. 1)
"Oil cutters" "Oil cutters"
Comes on when the cutters in the cross Comes on when the cutters in the cross
cut version must be oiled. The lubrication cut version must be oiled. The lubrication
procedure must be acknowledged on procedure must be acknowledged on
the reverse button (4) (see description in the reverse button (4) (see description in
"CUTTER MAINTENANCE"). "CUTTER MAINTENANCE").
8 = Control display (Fig. 1) 8 = Control display (Fig. 1)
"Door open"/ "Door malfunction" "Door open"/ "Door malfunction"
a) "Door open" a) "Door open"
Comes on if the door on the lower part Comes on if the door on the lower part
of the machine is opened. The machine of the machine is opened. The machine
switches off automatically and cannot switches off automatically and cannot
be started as long as the door remains be started as long as the door remains
open. open.
b) "Electrical fault" b) "Electrical fault"
Flashes when there is an electrical fault Flashes when there is an electrical fault
in the door sensor. The machine switches in the door sensor. The machine switches
off. Please contact your dealer. off. Please contact your dealer.
9 = Control display (Fig. 1) 9 = Control display (Fig. 1)
"Motor overload" / "Motor overload" /
"Electrical fault" "Electrical fault"
To find out what to do see the relevant To find out what to do see the relevant
description under the "MALFUNCTION" description under the "MALFUNCTION"
section. section.
a) "Motor protection" a) "Motor protection"
Comes on when the motor has been Comes on when the motor has been
overloaded and has switched off. The overloaded and has switched off. The
machine cannot be started while the machine cannot be started while the
motor is cooling down. motor is cooling down.
b) "Electrical fault" b) "Electrical fault"
Flashes when there is an electrical fault Flashes when there is an electrical fault
inside the control board. At the same inside the control board. At the same
time the function button (2) LED display time the function button (2) LED display
flashes. The machine switches off. flashes. The machine switches off.
Please contact your dealer. Please contact your dealer.
10 = Control display 10 = Control display
"Paper collection bag full" (Fig. 1) "Paper collection bag full" (Fig. 1)
Comes on when the paper collection bag is Comes on when the paper collection bag is
full and must be emptied. The cutting unit full and must be emptied. The cutting unit
for reducing paper switches off. for reducing paper switches off.
11 = Paper feed slot (Fig. 3) 11 = Paper feed slot (Fig. 3)
12 = Paper collection bag (Fig. 4) 12 = Paper collection bag (Fig. 4)
13 = Oil reservoir (Fig. 4 and 6) 13 = Oil reservoir (Fig. 4 and 6)
6
7
8
2
fig. 1
OPERATION
The shredder may not be used as a The shredder may not be used as a
step ladder or as a seat. Danger of step ladder or as a seat. Danger of
falling due to breakage! falling due to breakage!
SWITCHING THE MACHINE ON: SWITCHING THE MACHINE ON:
Proceed as follows to switch the machine to Proceed as follows to switch the machine to
"Ready": "Ready":
- Press the function button (2) briefly. - Press the function button (2) briefly.
- The function button (2) LED display - The function button (2) LED display
on for "Ready". on for "Ready".
- The machine can be loaded. - The machine can be loaded.

MATERIAL FEED:

MATERIAL FEED:
Feed paper into the cutting mechanism through Feed paper into the cutting mechanism through
the paper feed slot (11) (fig. 3). the paper feed slot (11) (fig. 3).
The machine automatically switches to forwards The machine automatically switches to forwards
running, draws the material in and automatically running, draws the material in and automatically
switches off after shredding. switches off after shredding.
Note: For shredding transparent films, the Note: For shredding transparent films, the
machine must be manually switched to forwards machine must be manually switched to forwards
running (press and hold the forwards button (3) running (press and hold the forwards button (3)
for approx. 2 secs.). for approx. 2 secs.).
By briefly pressing the function button (2) (Stop By briefly pressing the function button (2) (Stop
function), the shredding process can be stopped function), the shredding process can be stopped
at any time. To continue, press and hold the at any time. To continue, press and hold the
forwards button (3) for approx. 2 secs. forwards button (3) for approx. 2 secs.
If the machine is not used for a period of approx. If the machine is not used for a period of approx.
5 mins., it automatically switches off. 5 mins., it automatically switches off.
Never feed the shredder with a Never feed the shredder with a
quantity of material exceeding the quantity of material exceeding the
maximum indicated. maximum indicated.
TECHNICAL DATA section! TECHNICAL DATA section!
Should Should the the
overloaded, follow the instructions under overloaded, follow the instructions under
"MATERIAL JAM IN MACHINE" under "MATERIAL JAM IN MACHINE" under
"MALFUNCTIONS". "MALFUNCTIONS".
3
9
10
11
4
fig. 3
45 SC2/CC3/CC4/CC5/CC6 45 SC2/CC3/CC4/CC5/CC6
60 SC2/CC3/CC4/CC5/CC6 60 SC2/CC3/CC4/CC5/CC6
EMPTYING THE EMPTYING THE
PAPER COLLECTION BAG (Fig. 4): PAPER COLLECTION BAG (Fig. 4):
If the paper collection bag is full the machine If the paper collection bag is full the machine
switches off. The control display switches off. The control display
on. Proceed as follows: on. Proceed as follows:
- Open the door. The control display - Open the door. The control display
comes comes
- Take the collection bag (12) and the frame out - Take the collection bag (12) and the frame out
- Fit the emptied bag onto the bag frame and - Fit the emptied bag onto the bag frame and
- If the control display - If the control display
Note: The machine will only run if the door is Note: The machine will only run if the door is
closed. closed.
DYNAMIC LOAD DISPLAY: DYNAMIC LOAD DISPLAY:
To prevent a material jam and thus ensure a To prevent a material jam and thus ensure a
continual, effective destruction of the data continual, effective destruction of the data
carriers, the current load level of the motor is carriers, the current load level of the motor is
displayed during the shredding process by a displayed during the shredding process by a
coloured, diffuse light in the feed slot as follows: coloured, diffuse light in the feed slot as follows:
Green light: Green light:
Yellow light: Yellow light:
Red light: Red light:
Refer to the Refer to the
machine machine become become
5
6
comes on. If there is still material in one of comes on. If there is still material in one of
the feed slots, the control display the feed slots, the control display
comes on. comes on.
of the bottom part of the housing. Remove the of the bottom part of the housing. Remove the
bag and dispose of the contents. The control bag and dispose of the contents. The control
display display (10) goes out. (10) goes out.
insert the bag and the frame into the bottom insert the bag and the frame into the bottom
part of the housing again. Close the door. The part of the housing again. Close the door. The
control display control display (8) goes out. (8) goes out.
(6) comes on, press (6) comes on, press
the forward button (3) briefly. The remaining the forward button (3) briefly. The remaining
material in the feed slot is shredded and the material in the feed slot is shredded and the
display go out. display go out.
load < 50% load < 50%
load 50 - 75% load 50 - 75%
load 75 - 100% load 75 - 100%
13 12
fig. 4
(10) comes (10) comes
(8) (8)
(6) also (6) also