Electrical Connection - Parkside PKS 1500 A1 Instrucciones De Servicio

lease the handle (2) after completing the cut; instead
allow the machine head to move upwards slowly whilst
applying light counter pressure.
Mitre cut 0°- 45° (Fig. 1, 1.3)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important. To make miter cuts (inclined saw head), the
adjustable stop rail (27a) must be fixed at the outer
position.
• Open the set screw (27b) for the adjustable stop rail
(27a) with an Allen key and push the adjustable stop
rail outwards.
• The adjustable stop rail (27a) must be fixed far enough
in front of the innermost position that the distance
between the stop rail (27a) and the saw blade (5)
amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (27a) and
the saw blade (5) cannot collide.
• Secure the locking lever (27b) again.
• Move the machine head to the top position.
• Fix the rotary table (9) in the 0° position.
• Loosen the set screw (23) and use the handle (2) to
angle the machine head to the left, until the pointer
(25) indicates the desired angle measurement on the
scale (24).
• Re-tighten the fixing screw (23).
• Cut as described in section "Cross-cutting".
Saw blade replacement (Fig. 5)
• Pull out the mains plug.
• Place the saw unit in „cross-cutting" position
• Unlock the moving saw blade guard (6) by pressing
the lock (3 - Fig. 1); in the process, raise the saw bla-
de guard so that the saw blade is free.
• Actuate the spindle lock (22 - Fig. 3).
• Loosen the saw blade fastening screw (28) - (Atten-
tion: left-handed thread).
• Remove the screw (28) and saw blade flange (29).
• Carefully remove the saw blade (risk of injury from the
saw blade teeth).
• Place a new saw blade on the inner saw blade flan-
ge. In the process, observe the rotational direction of
the saw blade.
• Fit the outer saw blade flange and firmly tighten the
screw.
• Move the saw blade guard back to the correct position.
Replacing laser batteries (Fig. 6)
• Remove the laser battery cover (30). Remove the 2
batteries.
• Replace both batteries with the same or an equivalent
type. Make sure that they are inserted with the same
polarity as the used batteries.
• Close the battery cover.
Switch ON / switch OFF the laser
To switch on: Move the ON/OFF switch (33) of the la-
ser (34) to the "1" position. A laser line is projected on-
to the material you wish to process, providing an exact
guide for the cut.
8 GB/IE
(Fig. 6)
To switch off: Move the ON/OFF switch of the laser to
the "0" position.
Adjusting the laser (Fig. 7)
If the laser (31) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (32) and set the laser by moving sideways to
that the laser beam strikes the teeth of the saw blade
(5).
m Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions.
The customer's mains connection as well as the
extension cable used must also comply with these
regulations.
Important information
In the event of an overloading the motor will switch its-
elf off. After a cool-down period (time varies) the motor
can be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been impro-
perly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage re-
gularly. Make sure that the connection cable does not
hang on the power network during the inspection.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connection
cables with the marking „H 07 RN".
The printing of the type designation on the connection
cable is mandatory.
AC motor
• The mains voltage must be 230 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm2.
Connections and repairs of electrical equipment
may only be carried out by an electrician.
Please provide the following information in the event of
any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate