Technical Data; Auxiliary Handle - Bosch PROFESSIONAL GSB 13-2 Manual De Instrucciones

Technical data

Impact Drill
Part Number
Power
Amperage 127 V
220 V
No-Load speed
Impacts rate max.
Drill chuck clamping range – ∅
Concrete
Drill – ∅
Steel
Wood
Weight approx.
Safety Class
Operating controls
1. Quick clamping drill chuck
2. "Drilling/Impact Drilling" selector switch
3. Rotational direction switch (GSB 13 RE)
4. On/Off switch
5. Locking button for On/Off switch

6. Auxiliary handle*

7. Depth stop rod
8. Drill chuck key
* Not all of the accessories illustrated or described are included
as standard delivery.
Intended use
The machine is intended for impact drilling in brick, concrete
and stone as well as for drilling in wood, metal, ceramics and
plastics. Machines with electronic control and right/left
rotation are also suitable for screwing and thread-cutting.
Noise/vibration information
Measured values determined according to EN 50 144.
Typically the A-weighted noise levels of the product are:
sound pressure level: 97 dB (A); sound power level: 110 dB
(A).
Wear ear protection!
The typical weighted acceleration is 16 m/s
For your safety
Working safely with this machine is possible
only when the operating and safety information
are read completely and the instructions
contained therein are strictly followed. In addition, the
general safety instructions in the enclosed booklet must
be followed. Before using for the first time, ask for a
practical demonstration.
If the mains cable is damaged or cut through while
working, do not touch the cable but immediately pull
the mains plug. Never use the machine with a
damaged cable.
For long hair, wear hair protection.
Work only with closely fitting clothes.
Wear ear protection.
Wear safety goggles.
• Do not work materials containing asbestos. Asbestos is
considered carcinogenic.
• Take protective measures when dust can develop during
working that is harmful to one's health, combustible or
explosive. Example: Some dusts are regarded as
carcinogenic. Wear a dust mask and work with dust/chip
extraction when connectable.
• Insert the mains plug only when the machine is switched
off.
[w]
[A]
[A]
-1
[min ]
-1
[min ]
[mm]
[mm]
[mm]
[mm]
[kg]
E
2
.
GSB 13
0 601 13C 2..
550
4,6
2,6
3.000
48.000
13
13
10
25
1,7
/ II
• Always direct the cable to the rear away from the machine.
• When drilling use the auxiliary handle 6.
• Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal parts of
the tool "live" and shock the operator.
• If the drilling tool jams it will cause the tool to jolt. If this
occurs switch the tool off immediately.
• When working with the machine, always hold it firmly with
both hands and provide for a secure stance.
• Be careful when screwing in long screws; danger of sliding
off. (GSB 13 RE)
• For screws, work using the first gear or with a low speed.
(GSB 13 RE)
• Place the machine on the screw/nut only when switched
off. (GSB 13 RE)
• Always switch off the machine and allow to come to a stop
before placing it down.
• Never allow children to use the machine.
• Bosch is only able to ensure perfect functioning of the
machine if the original accessories intended for it are used.
Inserting the accessory
AUXILIARY HANDLE
• When drilling use the auxiliary handle 6.
Depending on the application, the auxiliary handle can be
adjustable in different positions.
DEPTH STOP ROD
For serial drills of same depth you have to put the depth stop
7 in the auxiliary handle and to adjust the according to your
necessity.
KEY TYPE CHUCK (FIGURE .A. )
Insert the accessory and tighten all 3 bores equally with the
chuck key 8.
SCREWDRIVER TOOLS (FIGURE .B. )
When using screwdriver bits 9, a bit holder 10 should always
be used. Use only the screwdriver bits that fit the screw
head.
Set selector switch 2 to the drill symbol for the screwing
function.
Check the material to be drilled and select the correct bit. Do
not drill with a bit that is inadequate for the job, because this
will damage either your workpiece or the bit itself.
Initial operation
• Do not drill, fasten or cut into blind areas where
electric, gas or water lines may exist. Use
appropriate detectors to determine if these lines
are hidden in the work area or call the local utility
company for assistance. Contacting electric lines may
cause fire or electric shock. Striking a gas line will probably
9
GSB 13 RE
0 601 13C 5..
550
4,6
2,6
0 – 3.000
0 – 48.000
13
13
10
25
1,7
E
/ II
GB