Accessories - Bosch HDD80051UC Instrucciones De Instalación

Ocultar thumbs Ver también para HDD80051UC:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ACCESSORIES

Flexible Blower
Bosch DHG602DUC
MODEL
DESCRIPTION
Non-Duct Recirculating Kit
Used in applications where ducting is not
feasible or available. Mount to toe kick
or base of a cabinet and attach directly
to DHG602DUC Flexible Blower using
8" (203 mm) round duct. Kit can be
rotated so that the exhaust is not directly
HDDREC5UC
at your feet. Includes decorative cover
HDDFILTUC
plate.
(replacement fi lter)
Rough-in Plate - 6" (152 mm) Round
Use for applications where 6" (152 mm)
round duct or elbow attaches to front
of airbox (inline or remote blower
installation).
HDDFTRAN6
Rough-in Plate - 8" (203 mm) Round
Use for applications where 8" (203 mm)
round duct or elbow attaches to front
of airbox (DHG602DUC inline blower
installation).
HDDFTRAN8
Gas Cooktop Seal Kit - 30-in. (762 mm),
36-in. (914 mm)
Used to provide seal between gas
cooktop and downdraft. Also includes
cabinet hole cover plates. Two grilles are
provided in the kit, you may only need
HDD0RSP
one for your specifi c installation.
HDD6RSP
Rectangular Duct - 2-ft. (0.6 m) sections
(1-7/8" x 19"/48 mm x 483 mm)
Galvanized steel construction 2-ft. (0.6 m)
sections can be connected together.
HDD2RECTD
Rectangular Adapter for
1-7/8" x 19" (48 mm x 483 mm)
Use to connect 1-7/8" x 19" (48 mm x
483 mm) rectangular duct directly to
downdraft when using side, below or rear
HDDSTRAN2
exhaust.
English 12
(purchase separately)
Inline and Remote Blowers
Bosch Models DHG6023RUC, DHG6015NUC
MODEL
DESCRIPTION
1-7/8" X 19" (48 mm x 483 mm) to
6" (152 mm) Round
Transition
Rectangular to 6" (152 mm) round
transition for left, right, below, or rear
exhaust - using Model DHG602DUC Flex
Blower. Can be attached to downdraft
unit or rectangular duct (HDD2RECTD).
HDDSTRAN6
1-7/8" X 19" (48 mm x 483 mm) to
8" (203 mm) Round
Transition
Rectangular to 8" (203 mm) round
transition for left, right, below, or rear
exhaust - using Inline or Remote Blower.
Can be attached to downdraft unit or
rectangular duct (HDD2RECTD).
HDDSTRAN8
Extension Cable - 25-ft. (7.62 m)
The remote or inline blower harness
should be routed through the knockout
and secured with a 3/4" (19 mm) strain
relief. The 25-ft. Extension Cable can
Connects to Hood
B
then be connected to the Adapter Cable
Connects to Remote
C
included in EXTNSET4 Accessory Kit
or In-line Blower
and then to the hood electrical panel.
EXTNCB25W
Extension Cable Connection Kit
Cable connection kit containing (4)
EXTNSET4
accessory cable adapters to connect a
variety of blower and hood combinations.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Hdd86051uc

Tabla de contenido