Install Roof Cap, Wall Cap, Inline Or Remote Blower; Connect Ductwork; Install The Electrical Panel; Plan House Wiring - Bosch HDD80051UC Instrucciones De Instalación

Ocultar thumbs Ver también para HDD80051UC:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

INSTALLATION
D
Clean housing surface (B) with Isopropyl Alcohol or
Rubbing Alcohol. Remove TAPE STRIPS to reveal
adhesive side of tape from the back side of TRIM
BRACKET (A).
E Center trim bracket left-to-right at TOP OF
DOWNDRAFT HOUSING (B). Stick trim bracket to
downdraft housing so that FLANGES (C) and (D) are
fl ush with each other.
F Cut TRIM SEAL (E) to length: No shorter than
downdraft countertop cutout opening and no longer
than cooktop width.
G Remove tape backing from TRIM SEAL (E). Center
trim seal left-to-right and stick trim seal across both
FLANGES (C) and (D).
E
B
E
A
D
Install roof cap, wall cap, inline or
remote blower
1. Follow instructions included with caps, inline and remote
blower.

Connect ductwork

1. From roof cap, wall cap, or remote blower - work back
towards the cabinet, attaching all ductwork, elbows and
transitions as previously planned.
2. Connect ductwork (and transition, if required) to fl ex blower
or downdraft. If necessary, use (2) no. 8-18 x .375 (9.5 mm)
Phillips screws for transition.
NOTE: Regardless of blower placement/exhaust, ensure
that all seams are properly taped - to make them secure
and air-tight. This includes seams/gaps between panels
and/or on the blower.
G
D
C
F

Install the electrical panel

(if previously removed from downdraft housing)
1. If electrical panel was removed from the downdraft housing
in order to mount it in a remote location: Mount electrical
panel in chosen location.
NOTE: Do not mount electrical panel with slots in cover
facing downward.

Plan house wiring

WARNING
RISK OF ELECTRIC SHOCK
Parts inside the appliance can have sharp edges. The
connection cable can be damaged. Do not bend or
pinch connection cables during installation.
Before connecting the appliance, check the house wiring
to make sure it has suffi cient circuit protection. The voltage
and frequency of the appliance must match the electrical
installation (see rating plate).
Only a qualifi ed electrician following all appropriate
regulations may lay or replace the connecting cable.
Follow all regulations, codes, and laws.
Ensure that the electrical connection meets the
requirements of the latest version of all regulations,
codes, and laws in the appropriate country, especially the
following standards:
National Electrical Code, ANSI/ NFPA 70, or CSA
Standards C22.1-94, Canadian Electrical Code, Part 1
and C22.2 No.0-M91, UL 507.
Have a qualifi ed electrical technician check the grounding
of the appliance.
Do not ground to a gas line.
Keep these installation instructions for future reference.
Ensure that the wire diameter meets the requirements of
the latest version of all applicable regulations, codes, and
laws in the appropriate country, especially the following
standards:
National Electrical Code, ANSI/NFPA 70, or CSA
Standards C22.1-94, Canadian Electrical Code, Part 1
and C22.2 No.0-M91.
The downdraft with the Flex Blower (purchase separately)
draws 3.0 Amps and requires a 120 VAC, 60 Hz circuit.
The downdraft with Remote Blower Models DHG6015NUC
and DHG6023RUC (purchase separately) draws 5.0 Amps
(max.) and requires a 120 VAC, 60 Hz circuit.
The downdraft has a 30-in. (762 mm) long power cord with
a 3-pronged plug. Plan to provide a grounded outlet in a
location which will allow the power cord to reach.
English 19

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Hdd86051uc

Tabla de contenido