Standard Accessories; Prior To Operation - HIKOKI G 12SA3 Instrucciones De Manejo

PRECAUTIONS ON USING DISC GRINDER
1. Never operate these power tools without Wheel Guards.
2. Check that speed marked on the wheel is equal to or
greater than the rated speed of the grinder.
Use only depressed center wheels rated at 80 m/s or
more.
3. Ensure that the wheel dimensions are compatible with
the grinder and that the wheel fi ts the spindle.
4. Abrasive wheels shall be stored and handled with care in
accordance with manufacturer's instructions.
SPECIFICATIONS
Model
Voltage (by areas)*
Power Input*
No-load speed
Outer dia. × Hole dia.
Wheel
Peripheral speed
Weight (Only main body)
*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Depressed center wheele .............................................1
(2) Wrench .........................................................................1
(3) Side handle ...................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Removal of casting fi n and fi nishing of various types of
steel, bronze and aluminum materials and castings.
○ Grinding of welded sections or sections cut by means of
a cutting torch.
○ Grinding of synthetic resins, slate, brick, marble, etc.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Fitting and adjusting the wheel guard
The wheel guard is a protective device to prevent injury
should the depressed center wheel shatter during
operation. Ensure that the guard is properly fi tted and
fastened before commencing grinding operation.
5. Inspect the depressed center wheel before use, do not
use chipped, cracked or otherwise defective products.
6. Always hold the body handle and side handle of the
power tool fi rmly. Otherwise the counterforce produced
may result in inaccurate and even dangerous operation.
7. Do not use cutting-off wheels for side grinding.
8. Do not use of separate reducing bushings or adapters to
adapt large hole abrasive wheels.
9. The wheel continues to rotate after the tool is switched
off .
G12SA3
(110 V, 120 V, 127 V, 220 V, 230 V, 240 V)
1300 W
11000 /min
115 × 22.23 mm
80 m/s
1.9 kg
By slightly loosening the setting screw, the wheel guard
can be turned and set at any desired angle for maximum
operational eff ectiveness. Ensure that the setting screw
is thoroughly tightened after adjusting the wheel guard.
5. Ensure that mounted wheels and points are fi tted in
accordance with the manufacturer's instructions. Ensure
that the depressed center wheel to be utilized is the
correct type and free of cracks or surface defects. Also
ensure that the depressed center wheel is properly
mounted and the wheel nut is securely tightened. Refer
to the section on "ASSEMBLING AND DISASSEMBLING
THE DEPRESSED CENTER WHEEL".
Ensure that blotters are used when they are provided
with the bonded abrasive product and when they are
required.
Do not use separate reducing bushings or adaptors to
adapt large hole abrasive wheels.
For tools intended to be fi tted with threaded hole wheel,
ensure that the thread in the wheel is long enough to
accept the spindle length.
Do not use cutting off wheel for side grinding.
6. Conducting a trial run
Ensure that the abrasive products is correctly mounted
and tightened before use and run the tool at no-load for
30 seconds in a safe position, stop immediately if there is
considerable vibration or if other defects are detected.
If this condition occurs, check the machine to determine
the cause.
7. Confi rm the push button
Confi rm that the push button is disengaged by pushing
push button two or three times before switching the
power tool on (See Fig. 2).
8. Fixing the side handle
Screw the side handle into the gear cover.
English
G13SB3
125 × 22.23 mm
6