General Power Tool Safety Warnings; Drill Safety Warnings; Functional Description - Makita 6402 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Low
2 High
3 Speed control screw
4 Switch trigger
SPECIFICATIONS
Model
Capacities
Steel ....................................................................................................... 10 mm
Wood ...................................................................................................... 21 mm
–1
No load speed (min ) ............................................................................... 0 – 1,200
Overall length ............................................................................................ 264 mm
Net weight .................................................................................................. 1.5 kg
Safety class ................................................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for drilling in wood, metal and plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.

General Power Tool Safety Warnings

WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

DRILL SAFETY WARNINGS

1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
Explanation of general view
5 Lock button
6 Reversing switch lever
7 Side grip
8 Tighten
7.
8.
ENE032-1
SAVE THESE INSTRUCTIONS.
ENF002-2 WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

GEA010-1
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
GEB001-6 "OFF" position when released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
A speed control screw is provided so that maximum tool
speed can be limited (variable).
Turn the speed control screw clockwise for higher speed,
and counterclockwise for lower speed.
Reversing switch action
For Model DP4700 (Fig. 2)
This tool has a reversing switch to change the rotational
direction. Move the reversing switch lever to the
tion for clockwise (forward) rotation or the
counterclockwise (reverse) rotation.
9 Chuck key
10 Sleeve
11 Ring
6402
/II
Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
DP4700
13 mm
36 mm
0 – 550
275 mm
2.2 kg
/II
posi-
position for
3