Optional Accessories - Makita GV7000 Manual De Instrucciones

Speed adjusting dial (Fig. 2)
The tool speed can be changed by turning the speed
adjusting dial to a given number setting from 1 to 5.
Higher speed is obtained when the dial is turned in the
direction of number 5. And lower speed is obtained when
it is turned in the direction of number 1.
Refer to the table below for the relationship between the
number settings on the dial and the approximate tool
speed.
Number
1
|
2
|
3
|
4
|
5
006385
CAUTION:
• If the tool is operated continuously at low speeds for a
long time, the motor will get overloaded and heated up.
• The speed adjusting dial can be turned only as far as 5
and back to 1. Do not force it past 5 or 1, or the speed
adjusting function may no longer work.
The tools equipped with electronic function are easy to
operate because of the following features.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the rotating speed is
kept constant even under load condition.
Soft start feature
Safety and soft start because of suppressed starting
shock.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing side grip (auxiliary handle) & cover
(Fig. 3 & 4)
CAUTION:
• Always be sure that the side grip is installed securely
before operation.
Install the cover, then screw the side grip on the tool
securely. The side grip and the cover can be installed on
either side of the tool.
Installing or removing abrasive disc (Fig. 5 & 6)
Mount the rubber pad onto the spindle. Fit the abrasive
disc on over the rubber pad and screw the lock nut onto
the spindle.
To tighten the lock nut, hold the spindle with the wrench
so that it cannot revolve, then use the lock nut wrench
and securely tighten clockwise.
To remove the disc, follow the installation procedure in
reverse.
OPERATION
Sanding operation (Fig. 7)
CAUTION:
• Always wear safety goggles or a face shield during
• Never run the tool without the abrasive disc. You may
RPM (/min)
2,500
Hold the tool firmly. Turn the tool on and then apply the
abrasive disc to the workpiece.
|
In general, keep the abrasive disc at an angle of about
2,800
15 degrees to the workpiece surface. Apply slight
pressure only. Excessive pressure will result in poor
|
performance and premature wear to abrasive disc.
3,500
MAINTENANCE
|
CAUTION:
4,200
• Always be sure that the tool is switched off and
|
4,700
• Never use gasoline, benzine, thinner, alcohol or the
Replacing carbon brushes (Fig. 8 & 9)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized or Factory Service Centers,
always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Rubber pad
• Abrasive discs
• Lock nut
• Wrench 17
• Lock nut wrench 28
NOTE:
• Some items in the list may be included in the tool pack-
operation.
seriously damage the pad.
unplugged before attempting to perform inspection or
maintenance.
like. Discoloration, deformation or cracks may result.
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
age as standard accessories. They may differ from
country to country.
5