Data Transmission - Roland XP-30 Manual Del Usuario

Universal Realtime System Exclusive messages
Master Volume
status data byte
F0H 7FH, 7FH, 04H, 01H, llH, mmH
Byte Remarks
F0H Exclusive status
7FH ID number
7FH device ID
04H sub ID#1
01H sub ID#2
llH LSB of Master Volume
mmH MSB of Master Volume
F7H EOX
* LSB of Master Volume (llH) is processed as 00H.

Data Transmission

This instrument can use exclusive messages to exchange many varieties of internal settings
with other devices.
The model ID of the exclusive messages used by this instrument is 6AH.
Data Request 1 RQ1
This message requests the other device to transmit data. The address and size indicate the
type and amount of data that is requested.
When a Data Request message is received, if the device is in a state in which it is able to
transmit data, and if the address and size are appropriate, the requested data is transmitted
as a Data Set 1 (DT1) message. If the conditions are not met, nothing is transmitted.
status data byte
F0H 41H, dev, 6AH, 11H, aaH, bbH,
ccH, ddH, ssH, ttH, uuH, vvH, sum
Byte Remarks
F0H Exclusive status
41H ID number
dev device ID
6AH model ID
11H command ID
aaH address MSB
bbH address
ccH address
ddH address LSB
ssH size MSB
ttH size
uuH size
vvH size LSB
sum checksum
F7H EOX
* The size of data that can be transmitted at one time is fixed for each type of data. and
data requests must be made with a fixed starting address and size. Refer to the address
and size given in "Mapa de direcciones de los parámetros" (p. 190).
* For the checksum, refer to (p. 204).
* This message is not received if the Rx.Exc parameter (SYSTEM/MIDI/SYS-EXC MIDI) is
OFF.
* This message is not received in GM mode.
status
F7H
(Universal Realtime message)
(Broadcast)
(Device Control Message)
(Master Volume)
(End Of Exclusive)
status
F7H
(Roland)
(dev: 10H - 1FH)
(XP-30)
(RQ1)
(End Of Exclusive)
Data Set 1 DT1
This message transmits the actual data, and is used when you wish to set the data of the
receiving device.
status data byte
F0H 41H, dev, 6AH, 12H, aaH, bbH,
ccH, ddH, eeH, ... ffH, sum
Byte Remarks
F0H Exclusive status
41H ID number
dev device ID
6AH model ID
12H command ID
aaH address MSB
bbH address
ccH address
ddH address LSB
eeH data:
: :
ffH data
sum checksum
F7H EOX
* The amount of data that is transmitted at one time is fixed for the type of data, and only
data of the fixed starting address and size will be transmitted. Refer to the address and
size given in "Mapa de direcciones de los parámetros" (p. 190).
* Data whose size is greater than 128 bytes should be divided into packets of 128 bytes or
less and transmitted. Successive ÒData Set 1Ó messages should have at least 20 ms of
time interval between them.
* For the checksum, refer to (p. 204).
* This message is not received if Rx.Exc parameter (SYSTEM/MIDI/SYS-EXC MIDI) is
OFF.
* This message is not received in GM mode.
This device is able to receive GS Exclusive messages only for Scale Tune settings.
Data Set 1 DT1
This message transmits the actual data, and is used when you wish to set the data of the
receiving device.
status data byte
F0H 41H, dev, 42H, 12H, aaH, bbH,
ccH, ddH, ... eeH, sum
Byte Remarks
F0H Exclusive status
41H ID number
dev device ID
42H model ID
12H command ID
aaH address MSB
bbH address middle byte
ccH address LSB
ddH data:
: :
eeH data
sum checksum
F7H EOX
* This message is not received when the Rx.Exc parameter (SYSTEM/MIDI/SYS-EXC
MIDI) is OFF.
* This message is not received in GM mode.
Aplicación MIDI
status
F7H
(Roland)
(dev: 10H - 1FH)
(XP-30)
(DT1)
The actual data to be transmitted. Multi-byte
data is transmitted in the order of the address.
(End Of Exclusive)
status
F7H
(Roland)
(dev: 10H - 1FH)
(GS)
(DT1)
The actual data to be transmitted. Multi-byte
data is transmitted in the address order.
(End Of Exclusive)
187