Support Leg - Hilti GX120-ME Manual De Instrucciones

WARNING
Parts of the tool outside the grip area may get hot when
fasteners are driven at a rapid rate over a long period of
time. Wear protective gloves.
7.1 Operation 6
NOTE
It is possible to drive a fastener only when more than 3
en
nails are in the magazine.
1. Position the nose of the tool at right angles to
the working surface and then press it against the
working surface as far as it will go.
2. Drive the fastener by pulling the trigger.
3. After driving the fastener, lift the tool away com-
pletely from the working surface.
7.1.1 Using pipe rings and other fasteners
If you wish to use pipe rings and other types of fastener,
push the plastic part of the fastener into the tool
nosepiece.
7.2 Gas level indicator 5
Please refer to section 6.4 "Checking the gas can (for 2
seconds)".
7.3 Fitting and removing the magazine
7.3.1 Removing the magazine 7
1. Pull the nail pusher back until it engages.
NOTE The nail pusher must engage in this position.
2. Remove all fasteners from the magazine.
3. Release the nail pusher and allow it to slide forward
slowly.
4. Push the locking lever down toward the magazine.
5. Pivot the magazine forward away from the tool.
6. Disengage the magazine from the tool.
7.3.2 Fitting the magazine 8
1. Engage the magazine with the tool.
NOTE The locking lever must be in the open posi-
tion.
2. Guide the magazine toward the tool until the shaped
parts fit together.
3. Close the locking lever and check that it engages.
7.4 Nosepiece
7.4.1 Removing the nosepiece 9
1. Set the power regulator to "Eject".
2. Remove the nosepiece.
7.4.2 Settings at the nosepiece
NOTE
When the power regulator is set to "+", the nosepiece is
set to the standard fastener driving depth.
NOTE
When the power regulator is set to "-", the nosepiece is
set to the reduced fastener driving depth.
20
NOTE
If the nail is still driven too deeply when the power
regulator is set to "-", it may be necessary to use a longer
nail.
7.4.2.1 Setting the standard fastener driving
depth 10
Set the power regulator to "+".
7.4.2.2 Setting the reduced fastener driving
depth 10
NOTE
This setting is suitable for fastening thin sheet metal to
soft materials (e.g. young / green concrete).
Set the power regulator to "-".
7.4.3 Fitting the tool nosepiece 11
WARNING
Check to ensure that the tool is not loaded. The tool
could be made ready to fire inadvertently by pressing the
nosepiece in by hand.
1. Align the nosepiece with the slot in the tool.
2. Push the nosepiece onto the tool.
3. While holding the nosepiece with the hand, press the
tool against the working surface until the nosepiece
engages in position.

7.5 Support leg

7.5.1 Fitting the support leg 12
1. Push the support leg into the slot in the magazine at
right angles.
2. Turn the support leg through 90° and engage it in
position.
7.5.2 Removing the support leg 13
1. Release the support leg by pressing the spring
catch.
2. Turn the support leg through 90°.
3. Pull the support leg away from the magazine at right
angles.
7.6 Bringing the piston into the correct position 14
NOTE
The piston is incorrectly positioned when the tool
nosepiece has not extended to its original position after
the tool is lifted away from the working surface and the
reset button is projecting.
The piston can be returned to the correct position by
pressing the reset button. Fasteners can then be driven.
In exceptional cases, the tool may fire without driving a
fastener when the tool is operated for the first time after
resetting the piston.
Press the reset button.