Programming Your Coffeemaker; Making Coffee - Cuisinart DCC-3000 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5. Flush filter by
running fresh
water through the
hole in bottom of
compartment for
10 seconds.
6. Allow the filter to
drain completely.
7. Place the assem-
bled water filter
holder into the
water reservoir,
pushing it down
to fit into place
(see figure 3).
Note: We recommend changing the water filter every
60 days or after 60 uses, and more often if you have
hard water. Replacement filters can be purchased in
stores, by calling Cuisinart Customer Service, or at
www.cuisinart.com.
BEFORE BREWING YOUR
FIRST POT OF COFFEE
During the manufacturing process, dust can get trapped
in your coffeemaker. We recommend flushing out the
system before brewing your first cups of coffee. Simply
fill the water reservoir and power on the unit. (See steps
#2 and #6 in MAKING COFFEE instructions, below).
DO NOT ADD COFFEE!
Once you've done that, brew your favorite coffee and
get ready to enjoy Cuisinart at its best!
PROGRAMMING YOUR
COFFEEMAKER
SETTING THE CLOCK
When the coffeemaker is plugged in, 12:00 will appear
until you set the time.
Turn the Function knob to CLOCK
Hold down the Hour or Minute button until the clock
begins flashing. Press either button to select the desired
time. Hold buttons down to scroll through the digits, or
press and release to advance one digit at a time. When
scrolling, the numbers will advance slowly and then
speed up, so as number displayed approaches the
desired time, press and release to advance one digit at
a time. Be sure the PM indicator is on if a PM time is
desired.
SETTING THE AUTO ON TIME
When you turn the Function knob to PROG, it displays a
previously selected Auto On time or the default time
(12:00pm).
Water
Reservoir
Charcoal
Water
Filter
figure 3
1. Turn the Function knob to PROG
Follow directions under SETTING THE CLOCK
(in previous section) to program your start-brew time.
2. Turn the Function knob to AUTO ON
LCD will display the current time.
3. Press and release ON/OFF button
A green light indicates that the coffeemaker is in
Auto On mode. The blue ON/OFF light will come on
when brew cycle begins. Both lights will go off when
Keep Warm cycle ends.
NOTE: To start brew time at the same time the next
day, simply make sure the Function knob is on Auto
On and press and release ON/OFF button once more.
Green Auto On light will go on.
SETTING THE AUTO OFF TIME
Turn the Function Knob to AUTO OFF
The default Auto Off time is set to turn the coffeemaker
off two hours after brewing is complete. Follow
directions under SETTING THE CLOCK (in previous
section) to program your coffeemaker to shut off from 0
to 4 hours after brew cycle is finished.

MAKING COFFEE

1. Insert charcoal water filter
Follow directions on page 6 for the preparation and
insertion of the filter.
2. Fill the water reservoir
a. Remove lid from reservoir, then lift reservoir
straight up and away from the coffeemaker.
b. Fill reservoir with water for the number of cups
you are brewing, replace the lid and return to unit.
(see figure 1). NOTE: If only brewing 2 cups fill with
water to the first line marking on the side of the
water reservoir.
NOTE: If water gets under the coffee tank or water
reservoir, it will end up in the drip tray.
3. Set preferences
Push the 1–4 Cup button if you are brewing fewer
than 5 cups.
4. Add the ground coffee
Insert a #4 paper filter OR permanent filter into the
filter basket. Be sure that the paper filter is completely
open and fully inserted in the basket. Add 1 scoop (1
tablespoon = ~6 grams) of ground coffee per cup.
Adjust the amount according to taste.
figure 4
8

Publicidad

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

Dcc-3000p1

Tabla de contenido