Set Menu; Using Set Menu; Sound Menu - Yamaha HTR-6230 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Set menu

Using set menu

Use the remote control to access and adjust each
parameter.
y
• You can change the set menu parameters while this unit is reproducing
sound.
1
Press kMENU on the remote control.
"AUTO SETUP" appears on the front panel display.
2
Press ok / n to select "MANUAL SETUP."
.
MANUAL SETUP
3
Press oENTER to enter "MANUAL SETUP."
"1 SOUND MENU" appears on the front panel
display.

1 SOUND MENU

4
Press ok / n repeatedly and then press
oENTER to select and enter the desired
menu.
The following menus appear on the front panel
display as you press ok / n repeatedly.
1 SOUND MENU
2 INPUT MENU
3 OPTION MENU
5
Press ok / n repeatedly and then press
oENTER to select and enter the desired
submenu.
• Repeat this step to navigate to and enter the items
you want to adjust.
• To return to the previous menu level, press
qRETURN.
6
Press ok / n to select the desired parameter
and then ol / h to change the parameter
value.
• Press oh to increase the value.
• Press ol to decrease the value.
7
Press kMENU to exit from set menu.
32
En
1 SOUND MENU
Use this menu to manually adjust any speaker settings or
compensate for video signal processing delays when using
LCD monitors or projectors.
y
• Initial settings are indicated by (*) in this following each parameter.
Speaker settings
Use this feature to manually adjust any speaker settings.
FRONT B speaker setting
Use this feature to select the location of the front speakers
connected to the FRONT B terminals.
Choice
FRONT*
When FRONT B speakers are set in the main zone.
ZONE B
When FRONT B speakers are set in another zone. This
setting mutes all the speakers in the main room when
FRONT B is selected by CSPEAKERS.
Notes
• If you connect headphones to the PHONES jack on this unit, the sound is
output from both headphones and the FRONT B terminals while
"FRONT B" is set to "ZONE B."
• If a DSP program is selected when "FRONT B" is set to "ZONE B," this
unit automatically enters the Virtual CINEMA DSP mode (see page 26).
Front speakers, Center speaker, Surround
left/right speakers
FRONT, CENTER, SUR. LR
Select "LARGE (LRG)" or "SMALL (SML)" depending
on the size of your each speaker. When Center speaker or
Surround speakers is not connected, select "NONE."
Initial setting:
FRONT: "LARGE"
CENTER: "SML"
SUR. LR: "SML"
Woofer diameter of a speaker is 16 cm (6.5 in) or
larger: LARGE (LRG)
Woofer diameter of a speaker is smaller than 16 cm
(6.5 in): SMALL (SML)
Notes
• When "BASS OUT" is set to "FRONT" on this page, you can select only
"LARGE" in "FRONT." If "FRONT" is set to a setting other than
"LARGE" in advance, this unit automatically changes the value to
"LARGE."
• When you select "NONE" in "CENTER," the center channel signals are
directed to the front left and right speakers.
• When you select "NONE" in "SUR. LR," this unit is automatically enters
the Virtual CINEMA DSP mode (see page 26).
BASS OUT
LFE/Bass out
Use this feature to select the speakers that output the LFE
(low-frequency effect) and the low-frequency signals.
y
• If you are not satisfied with the bass sounds from your speakers, you can
change these settings according to your preference.
A)SPEAKER SET
FRONT B
Condition

Publicidad

Tabla de contenido
loading

Tabla de contenido