Phono Encoding - lauson CL136 Manual De Instrucciones

3. PRESS THE "
ENCODING IS NOW PERFORMING.
4. PRESS THE "
5. AFTER COMPLETED OF ENCODING ACCORDING TO THE PRESET PROGRAM, UNIT WILL STOP
PLAYBACK AUTOMATICALLY.
REMARK:-
- SAME OPERATION PROCEDURE FOR ENCODING TO SD/MMC CARD.
- IF BOTH RECRODING SOURCE (USB PEN DRIVE AND SD/MMC CARD) BEING DETECTED BY THE
SYSTEM DURING ENCODING, PLEASE PRESS "SKIP UP
THE DESIRE SOURCE. THEN PRESS "
- THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE CD TRACK
- THE SYSTEM WILL CREAT A " AUDIO " FOLDER AND THEN STORE THE ENCODING TRACK IN IT.
- THE RECORDING FORMAT IS PRESET AT – MP3
- NO SONG TITLE WILL BE RECORDED DURING ENCODING MODE
- TO INTERRUPT THE RECRODING, PRESS THE"
- RECORDING WILL BE COMPLETED ONLY ENTIRE SONG BEING ENCODED, IF TERMINATE THE
ENCODING PROCESS INTERMEDIATELY, THERE IS NO TRACK BEING RECORDED NOR STORED TO
THE USB OR SD/MMC CARD
III) COPYING OF MP3/WMA FILE
IF PUTTING A MP3/WMA DISC INSTEAD OF A CD-DISC, THE SYSTEM WILL COPY THE FILES TO THE USB OR
SD/MMC CARD IF PRESS THE "
ENCODING AS STIPULATE ON ABOVE, AND THE SYSTEM WILL SWITCH TO COPYING MODE ONLY IF
MP3/WMA FILE BEING READ.
REMARK:
- THE SYSTEM WILL STORE THE FILE TO USB SOURCE FIRST IF BOTH USB AND SD SLOT ARE BEING
OCCUPLIED BY STORAGE MEDIA.
- THE SYSTEM WILL CREAT A " FCOPY " FOLDER AND THEN STORE ALL COPY FILE IN IT.
- IF PRESS THE" REC " BUTTON (15) DURING PLAYBACK OF USB OR SD SOURCE, THE FILE WILL COPY
FROM USB TO SD OR SD TO USB.
B) PHONO ENCODING
1) SELECT " PHON/AUX " MODE AND THEN PRESS THE "
2) THE LCD DISPLAY (2) WITH SHOW "
THE SYSTEM IS STARTING THE ENCODING MODE.
3) START PLAYBACK AT PHONO FOR THE TRACK WHICH YOU WANT TO RECORD TO USB POSITION.
4) AFTER FINISH OF RECODING, PRESS THE "
(2) STOP FLASHING AND RETURN TO " PHON/AUX " MODE.
C) RADIO ENCODING
1) SELECT " TUNER " MODE AND THEN SELECT THE DESIRE RADIO STATION
2) PRESS THE" REC " BUTTON (15) TO START THE ENCODING.
3) THE LCD DISPLAY (2) WITH SHOW "
THE SYSTEM IS STARTING THE RECORDING.
4) AFTER FINISH OF RECODING, PRESS THE "
(2) STOP FLASHING AND RETURN TO " TUNER " MODE.
REMARK:-
- IF THE RADIO RECEPTION SIGNAL IS NOT STRONG ENOUGH, THE SYSTEM CANNOT START THE
ENCODING PROCESS AND THE TEXT " NO GOOD " WILL SHOW ON THE LCD DISPLAY (2).
- THE RECRODING QUALITY AND PERFORMANCE FOR RADIO ENCODING IS NOT STABLE DUE TO
INTERFERENCE OF RADIO RECEIPTION. THIS IS NOT A MAUFUNCTION OF THE SYSTEM.
- DUE TO THE INTERFERENCE, THE SYSYTEM WAS NOT ABLE TO ENCODE AM RADIO.
D) AUX-IN ENCODING
CONNECT ANOTHER AUDIO DEVICE, E.G. (PORTABLE) CD PLAYER, MP3 PLAYER, (PORTABLE) CASSETTE
PLAYER, IPOD, ETC. TO THIS SYSTEM VIA A CORD WITH 3.5MM DIA JACK PLUGS (NOT SUPPLIED).
CONNECT ONE END OF THIS CORD TO THE 3.5MM DIA. HEADPHONE JACK ON THE EXTERNAL DEVICE AND
THE OTHER END TO THE 3.5MM AUX-IN JACK (5) ON THE SIDE OF THE UNIT.
WHEN CONNECTED IN THIS WAY IT IS POSSIBLE TO:
SELECT "PHONO/AUX" MODE. ONCE 3.5MM PLUG PLUGGED T THE AUX IN JACK. CHANNEL WILL
CHANGE TO AUX IN AUTOMATICALLY.
• PLAY BACK THE MUSIC ALREADY ON THE CONNECTED DEVICE.
• ENCODE AND CONVERT THE MUSIC FILES FROM THE CONNECTED DEVICE TO USB/SD INTO MP3
FORMAT. FOLLOW THE SAME PROCEDURE AS DESCRIBED IN THIS MANUAL.
" BUTTON (15) AND THE UNIT WILL DISPLAY "
" BUTTON (15) REPEATLY AGAIN TO SELECT " REC_ALL ".
REC " BUTTON (15) AGAIN TO CONTINUOUS THE PROCESS.
REC " BUTTON (15). THE OPERATION PROCEDURES IS SAME AS CD
" & "
STOP
" & "
STOP
OR DOWN
BIT RATE : 128 KBPS, SAMPLING RATE : 44.1KHZ
STOP
" BUTTON (19) DURING RECORDING MODE.
REC " BUTTON (15) DIRECTLY.
" AND FLASHING AFTER FEW SECONDS. NOW
" BUTTON (19) UNTIL THE TEXT ON LCD DISPLAY
" AND FLASHING AFTER FEW SECONDS. NOW
" BUTTON (19) UNTIL THE TEXT ON LCD DISPLAY
GB-6
" & " " AND FLASHING.
" BUTTON (18/20) TO SELECT