General Power Tool Safety Warnings - Worx Jawsaw WG307 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

GeneRAL POWeR TOOL
SAfeTy WARnInGS
wArNiNG: Some dust created by
power sanding, sawing, grinding,
drilling and other construction activities
contains chemicals known to the state
of california to cause cancer, birth
defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints;
• Crystalline silica from bricks and
cement and other masonry products
and
• Arsenic and chromium from
chemically-treated lumber.
your risk from these exposures varies,
depending on how often you do this
type of work. To reduce your exposure
to these chemical: work in a well
ventilated area, and work with approved
safety equipment, such as those dust
masks that are specially designed to
filter out microscopic particles.
rEAd ALL iNSTrucTioNS and safety
information very carefully and make
sure you fully understand them before
attempting any operations with this tool.
iNdENdEd uSE:
Your WORX JAWSAW has been designed for
consumer use only. It is intended for pruning
branches and cutting small logs up to 4 inches
(100mm) in diameter.
NoMENcLATuEr
a) Bucking – The process of cross cutting a
felled tree or log into lengths.
b) JawSaw power head – A JawSaw without
the saw chain and guide bar.
c) Drive Sprocket or Sprocket – The toothed
part that drives the saw chain.
d) Front Handle – The support handle located
at or toward the front of the JawSaw.
e) Guide Bar – A solid railed structure that
supports and guides the saw chain.
f) Normal Cutting Position – Those positions
assumed in performing the bucking and
delimbing cuts.
Guarded electric chain saw
g) Oiler Control – A system for oiling the
guide bar and saw chain.
h) Rear handle (push handle) – The support
handle located at the rear of the saw.
i) Replacement Saw Chain – A chain that
is the saw manufacturer's replacement
catalogue (or equivalent) number.
j) Saw Chain – A loop of chain having cutting
teeth, that cut the wood, and that is driven
by the motor and is supported by the
guide bar.
k) Trigger Switch – A device that when
operated will complete or interrupt an
electrical power circuit to the motor of the
JawSaw.
l) Switch Linkage – The mechanism that
transmits motion from a trigger to the
switch.
m) Lock out button – A movable stop that
prevents the unintentional operation of the
switch until manually actuated.
For JawSaw nomenclature, please refer to the
coMPoNENT LiST.
wArNiNG: When using an electric
JawSaw, basic safety precautions
should always be followed to reduce the risk
of fire, electric shock, and injury to persons,
including the following:
For doubLE-iNSuLATEd JAwSAwS
a) rEPLAcEMENT PArTS
When servicing use only identical
replacement parts.
b) PoLAriZEd PLuGS
To reduce the risk of electric shock, this
equipment has a polarized plug (one blade
is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician
to install the proper outlet. Do not change the
plug in any way.
c) For ALL JAwSAwS
1) keep work area clean.
Cluttered areas invite injuries.
Do not start cutting until you have a clear
work area, secure footing, and a planned
retreat path from the falling limbs.
2) consider work area environment. use
11
11
en

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Jawsaw wg308

Tabla de contenido