Worx Jawsaw WG307 Manual De Instrucciones página 21

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Turn off and unplug saw before moving
from one place to another.
ASSeMBLInG THe
eXTenSIOn POLe (OnLy
fOR MODeL WG308)
wArNiNG: before attaching the
extension pole (20), make sure that
the tool is switched off and unplugged.
1. Turn the release lever to allow the handle
clamp to spring open (See Fig. Z1).
2. With the pole slightly angled away from
the tool, insert the steel tab into the slot
behind the front handle, then swing the
pole towards the tool's rear handle. (See
Fig Z2).
3. Position the pole handle clamp inside the
JawSaw's rear handle as shown in Fig
Z3. To allow the clamp to properly fit the
handle, push lockout button and depress
the trigger.
4. Close the clamp, the locking lever will
automatically lock into place.
5. Check that the rear handle is properly
fitted to the clamp and check that the
clamp is properly set in the lock position.
6. Plug in the tools power cord to the
extension pole power cord
Z4)
wArNiNG! before attaching the
power cord of the machine to the
power cord of the extension pole (
in Fig. Z4), make sure that the tool is
switched off and unplugged from the
power supply.
wArNiNG! when using this
machine with the extension pole,
make sure that attaching the power
cord of the machine to the power cord
of the extension pole, and then attach
the power cord of the extension pole to
power supply.
wArNiNG! ELEcTrocuTioN
hAZArd
Never use the JawSaw or extension pole in
an area with overhead power lines or where
the branch being cut can come into contact
Guarded electric chain saw
with overhead power lines.
cuTTiNG wiTh ExTENSioN PoLE (oNLy
For wG308)
1. Attached the pole as described in
2. Connect the JawSaw to extension cord.
3. Lift JawSaw with extension pole upward
4. Before cutting a high branch, consider all
bystanders far away. do not stand on a
ladder or other type of unstable support
while using the tool. do not use the tool
near cable, electrical power or telephone
. (See Fig.
lines. keep 10ft (3m) away from all
power lines. (See Fig. Ab1-Ab4)
5. Position the Jaw perpendicularly on the
6. One hand should firmly grip the push
7 .
8. At the completion of the cut, be ready to
of the cut, this may damage the tool.
''Assembling the extension pole''.
Connect extension cord to power supply.
NoTE: The JawSaw is quite heavy on the
end of the extension pole.
Add the pole attachment when cutting
limbs above shoulder height and remove
the pole saw when cutting limbs at or
below shoulder height.
one step by one step (See Fig. AA). To
raise to the vertical position, lift by the
Jawsaw first, then hand over hand along
the pole.
the same points detailed in the previous
section "Trimming Branches" but pay
particular attention to the likely path of the
falling branch.
wArNiNG: do not stand directly
below a branch being cut. keep
branch being cut.
NoTE: Maximum cutting capacity of
JawSaw is 4 inches (10cm).
handle of the extension pole. The other
hand should hold the metal portion of the
pole or the sliding handle on the pole (See
Fig. AC).
Complete the cut as described in
"Trimming Branches" .
immediately support the weight of the
entire tool as the branch falls.
wArNiNG: do not let the JawSaw
fall to the ground at the completion
21
21
en

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Jawsaw wg308

Tabla de contenido