Setting Into Operation; Connecting The Receiver; Inserting The Batteries Into The Transmitter; Wireless Microphone 1 - IMG STAGELINE TXS-611SET Manual De Instrucciones

www .cept .org
t ECC
t Topics
t Short Range Devices (SRD) and other R&T TE
sub-classes
t EFIS and National Frequency Tables

4 Setting into Operation

4.1 Connecting the receiver

1) Connect the receiver to the following unit (e . g .
amplifier, mixer) . For this purpose, two audio
outputs are provided:
– MIC OUT (10) as an XLR jack, balanced to
connect a microphone input
– LINE OUT (11) as a 6 .3 mm jack, unbal . to
connect an input with line level; use the con-
nection cable provided
2) Connect the power supply unit provided to the
power supply jack (8) and to a mains socket
(230 V/ 50 Hz) .
4.2 Inserting the batteries into the
transmitter
For operating the wireless microphone and the
pocket transmitter, two 1 .5 V batteries of size AA
are required .
•
Always insert (rechargeable) batteries of the
same type and always replace all of them .
•
If the transmitter is not in use for a longer period
of time, always remove the batteries to prevent
damage to the unit in case of battery leakage!
Used batteries and defective rechargeable
batteries must not be placed in the house-
hold waste . To protect the environment,
always take them to a special waste dis-
posal, e . g . collection container at your
retailer .
4.2.1 Wireless microphone
To open the battery compartment (17), press the
arrow of the battery compartment cover and push
the cover downwards .
Insert the batteries with the positive and neg-
ative poles as indicated in the compartment, then
replace the cover .
12
1

4.2.2 Pocket transmitter

To open the battery compartment (28), press the
arrow of the battery compartment cover (24) and
push the cover downwards .
Insert the batteries with the positive and neg-
ative poles as indicated in fig . 3, then replace the
cover .
4.3 Connecting and attaching
the tie clip microphone
and the pocket transmitter
1) Connect the plug of the tie clip microphone
to the 3 .5 mm jack (25) of the transmitter . To
prevent accidental disconnection, secure the
plug with the cap nut .
2) Attach the tie clip microphone to your clothes,
as close to your mouth as possible .
3) After all adjustments have been made (chap-
ters 4 .4 and 5), use the clip (26) to attach the
transmitter to your clothes (e . g . belt or waist-
band) .

4.4 Adjusting the transmission channel

To adjust a free transmission channel on the re-
ceiver, either use the automatic scan function or
adjust the channel manually . Then simply press
a button to adjust the wireless microphone
the pocket transmitter
IR signal .
1) Switch on the receiver with the POWER switch
(9) . To switch on the pocket transmitter, set the
switch (21) to the position ON . To switch on the
wireless microphone, set the switch (16) to the
upper position . After switching on, the corre-
sponding display (3, 14, 22) lights up .
2) To automatically scan a free channel, press the
button SELECT (2) briefly . To indicate the scan,
one segment of the numerical display element
starts moving around on the display (3):
After a while, the display shows the number of
the channel found . The correspond ing frequen-
cies can be found in the tables on page 40 .
3) To manually adjust a specific transmission
frequency, find the corresponding channel num-
ber in the tables on page 40 . To adjust the
for TXS-611SET and TXS-616SET only
1
for TXS-631SET and TXS-636SET only
2
2
2
2
to the same channel via
2
or
1