Assembly - Ryobi BS903 Manual Del Operador

UNPACKING
This product requires

assembly.

 Carefully remove the tool and any accessories from the
box. Place it on a level work surface.
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
 Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
 Do not discard the packing material until you have carefully
inspected and satisfactorily operated the tool.
 If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
WARNING:
If any parts are damaged or missing, do not operate this
tool until the missing parts are replaced. Failure to do so
could result in possible serious personal injury.
WARNING:
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
MOUNTING BAND SAW TO WORKBENCH
If the band saw is to be used in a permanent location, we
recommend that you secure it to a workbench or other
stable surface. When mounting the saw to a workbench,
holes should be drilled through the supporting surface of
the workbench.
 Each hole in the saw base should be bolted securely
using bolts, lock washers, and hex nuts (not included).
 Place band saw on the workbench. Using the saw base
as a pattern, locate and mark the holes where the band
saw is to be mounted.
 Drill holes through the workbench.
 Place band saw on the workbench aligning holes in the
saw base with the holes drilled in the workbench.
 Insert bolts (not included) and tighten securely with lock
washers and hex nuts (not included).
NOTE: All bolts should be inserted from the top. Install
the lock washers and hex nuts from the underside of the
bench.
ASSEMBLy
Supporting surface where band saw is mounted should be
examined carefully after mounting to insure that no movement
during use can result. If any tipping or walking is noted,
secure workbench or support surface before beginning
cutting operation.
CLAMPING BAND SAW TO WORKBENCH
see Figure 5, page 18.
If the band saw is to be used as a portable tool, it is
recommended that you fasten it permanently to a mounting
board that can easily be clamped to a workbench or other
supporting surface. The mounting board should be of
sufficient size to avoid tipping of saw while in use. Any
good grade plywood or chipboard with a 3/4 in. thickness
is recommended.
 Mount saw to board using holes in saw base as a template
for hole pattern. Locate and mark the holes where the
band saw is to be mounted.
 Follow the last three steps in the section Mounting Band
Saw to Workbench, shown above.
If lag bolts are used, make sure they are long enough to
go through holes in the saw base and material the saw is
being mounted to. If machine bolts are being used, make
sure bolts are long enough to go through holes in the saw
base, the material being mounted to, and the lock washers
and hex nuts.
NOTE: It may be necessary to countersink hex nuts and
washers on bottom side of mounting board.
MOUNTING THE SAW TABLE
see Figures 6 - 7, pages 18 - 19.
 Loosen and remove the table aligning bolt, washer, and
wing nut on the saw table.
 Loosen the table extension knobs beneath the sliding
table extension by turning them clockwise.
 Slide the table extension out and retighten the table
extension knobs.
 Standing at the front of the band saw, slide the saw table
past the blade and through the slot moving from the right
side of the saw table to the left.
 Align the screw holes in the saw table with the holes in
the saw table bracket.
 Using the phillips screws, attach the saw table to the saw
table bracket. Tighten phillips screws securely.
 Close the sliding table extension, retighten the table
extension knobs, then attach the table aligning bolt,
washer, and wing nut to the saw table.
NOTE: The wing nut goes below the saw table.
9 — English