After Use - Dräger Oxy 3000 T Instrucciones De Uso

Donning devices with mouthpiece (without starter)
• Bring the mouthpiece up to your face.
In doing so, the mouthpiece cap is removed from the mouthpiece.
• Place the mouthpiece in your mouth.
In doing so, ensure that the breathing hose is not twisted.
The rubber piece should sit between the teeth and the lips.
• Simulate how to fill the breathing bag by breathing out powerfully
two or three times:
To do so, inhale from the environment and exhale into the mouth-
piece.
• Cover the mouthpiece tightly with your lips.
• Press the nose clip open
with one hand and place it
on the nose.
The nose must be closed
tightly.
• Hold the device as pictured
and pull on the end of the
neck strap, to lift the device.
Place the device in front of
the chest and do not lift it too
high. The device must not
pull on the mouthpiece.
• Remove corrective glasses if necessary.
• If necessary, release the goggles from the device and from the
button strap and put them on.
• Put the chest harness around your body and close it.
• Tighten the chest harness.
Donning devices with hood
NOTICE
People wearing corrective glasses should keep them on.
• Lift the hood.
The starter pin is pulled out of the device.
• Put on the hood.
Grasp the collar of the hood and widen it. Put your chin into the
collar first, then pull the hood over your head.
• Push long hair completely under the hood.
• Move the half mask in front of the mouth and nose.
Ensure that the breathing hose does not get twisted.
NOTICE
With the oxygen self-rescuer, the oxygen from the starter flows into
the breathing bag within 1 to 2 minutes. However, the breathing bag
does not fill completely. If necessary, use your hands to help unfold
the breathing bag. If the breathing bag does not fill, breath out pow-
erfully two or three times to fill the breathing bag.
Grasp the collar of the hood and lift the hood and half mask from
the face. Exhale directly into the half mask.
• Tighten the strap to the back.
If this is not possible, use your hand to press the half mask against
the face.
The half mask sits tightly in front of the mouth and nose, the collar
lies tight against the neck.
10
The half mask of the oxygen self-rescuer must fit snugly! Full
beards cause leakages. Leakages reduce the operating time and
affect the protective function.
Pull the strap again if you feel air passing through the half mask
when breathing.
• Put the chest harness around your body and close it.
• Tighten the chest harness.
Notes for the use of the oxygen self-rescuer
— Start the escape calmly, do not rush.
— Plan your escape route, choose the shortest way to safe ambient
air!
— Behave calmly. Short, quick breaths use more oxygen!
— In the case of devices with mouthpieces:
Always make sure that the mouthpiece is tight between your teeth
and lips and cover the mouthpiece tightly with your lips.
— In the case of devices with a hood:
Always ensure that the half mask sits snugly on the face.
— The air from the oxygen self-rescuer is warm and dry. This shows
that the oxygen self-rescuer is functioning correctly. A possible
strange taste is normal and harmless.
— Do not damage or compress the breathing bag, otherwise vital
oxygen is lost.
— If you need to vomit, take the mouthpiece out of your mouth and
close it with your thumb, or remove the hood. Do not vomit in the
oxygen self-rescuer!
In order to ensure that no harmful air is inhaled from the environ-
ment, first inhale from the oxygen self-rescuer once the mouth-
piece has been reinserted or the hood put back on.

After use

Cleaning the training device
FOR TRAINING ONLY
Only use the methods named for cleaning and disinfecting. Note
the dosing and exposure times! Do not use solvents such as petrol,
alcohol or similar materials.
The training device could otherwise be damaged.
• Take off the impact protection and strap from the training device
and clean them in soapy water.
• Dampen and brush down the training device.
The water should be hand-hot. A gentle cleaning agent (e. g.
Sekusept
Disinfecting the heat exchanger set
• Push the O-ring of the trai-
ning heat exchanger onto
the breathing hose and
loosen the training heat
exchanger from the brea-
thing hose.
• Put the training heat
exchanger in the disinfec-
tant (max. 30
Incidur
tion. Immediately after-
wards, remove the
disinfectant completely under running water.
Drying the training device
• Leave all parts to dry completely in a drying cabinet or in the open
air.
Maximum duration in the drying cabinet: 2 hours up to a
max. 60
1) Observe the corresponding Instructions for Use.
Sekusept
NOTICE
CAUTION
® 1)
Cleaner ) can be used.
o
C) with
1)
disinfectant solu-
o
C. Do not expose to direct sunlight.
®
is a registered trademark of Ecolab GmbH & Co OHG