Colour Radiator; Interconnecting Several Rgbl-120Dmx Units; Remote Control With The Lc-3; Funcionamiento Con - IMG STAGELINE RGBL-120DMX Manual De Instrucciones

c) Use button DOWN or UP to switch the music
control on or off and confirm with button ENTER.
The display returns to
selected programme starts and the display
shows again the number of the programme.
6) Adjust the control SENSITIVITY (11) for the micro-
phone so that the dynamic power of the music will
be reproduced by the colour change or by the run-
ning light in an optimum way. With each control sig-
nal which has been created by the sound picked up
by the microphone (12), the green LED SOUND (8)
shortly lights up.
Note: When the volume at the music system is modified, the
microphone sensitivity must be adapted accordingly with
the rotary control.

6.1.2 Colour radiator

The unit is capable of radiating one of 9 preset colours
at maximum brightness or a manually adjusted colour
at any desired brightness.
A Selecting a preset colour
1) Press button MENU (5) so many times until
displayed.
2) Activate the menu item with button ENTER (7).The
display shows the colour last adjusted (
oder ) in a flashing way.
3) Select a colour with button DOWN or UP (6)
[1 = white ... 9 = blue,
adjustment, next paragraph] and confirm with
button ENTER. The display stops blinking.
B Manual colour adjustment
Hint: When adjusting the brightness of the red, green, or
blue LEDs, not only their brightness will be modified but in
case of a combination of these colours, the shade of colour
will be modified. Therefore, first adjust the colour which is
intended to dominate to the desired brightness, and then
add the other two colours. For the combination white, first
adjust the brightness of the colour green, because this
colour appears to the eye to be the brightest colour. Then
add red to result in yellow and finally add blue to result in
white.
1) Press button MENU (5) so many times until the dis-
play shows .
2) Activate the menu item with button ENTER (7). The
display shows the colour last adjusted (
oder ) in a flashing way.
3) Use button DOWN or UP (6) to switch to
(manual). Activate the function with button ENTER.
The display now shows for the colour red and the
brightness value for the red LEDs.
4) Use button ENTER to switch to
green and to for blue and then back again to for
red.
5) Adjust the selected colour with button DOWN or UP
(indication 0 – 255) so that the desired shade of
colour with the desired brightness will result.
. After 8 seconds the
is
...
= manual colour
...
for the colour
6) For fine adjustment of the shade of colour a colour
can be selected again with button ENTER and be
readjusted with the buttons DOWN and UP.
7) If no button is actuated within 8 seconds, the display
returns to the indication
of colour, start again with operating step 1, if required.

6.2 Interconnecting several RGBL-120DMX units

Several RGBL-120DMX units may be interconnected.
Then all slave units can be controlled in sync with the
master unit.
1) Connect the DMX OUTPUT (14) of the master unit
via a 3-pole XLR cable (e. g. series MEC-... or
MECN-... from the product range of "img Stage
Line") to the DMX INPUT (15) of the first slave unit.
2) Connect the DMX OUTPUT of the first slave unit to
the DMX INPUT of the second slave unit, etc. until
all units have been connected in a chain.
No DMX signal must be present at the DMX INPUT of
the master unit, so that the yellow LED MASTER (4)
lights up and the unit is thus switched to the master
mode. Once the control signals from the master unit
are applied to the slave units, the red LED SLAVE (9)
will light up on the slave units. The slave units are then
automatically switched to the slave mode and can be
controlled in sync with the master unit.

6.3 Remote control with the LC-3

The remote control LC-3 available as an accessory
allows to control various functions. There must be no
DMX signal at the DMX INPUT (15).
1) Connect the remote control to the jack REMOTE
CTRL ONLY (13).
2) Via the DMX OUTPUT (14), further RGBL-120DMX
units may be connected (
control them together with the master unit via the
remote control.
3) With button STAND BY (18), the LEDs of the light
effect panel can be switched on or off. When the
LEDs are switched off, the LED next to button
STAND BY will light up as a check.
4) Use button MODE (20) to select the desired function:
Programm Nr. 0 (
– The LED of button MODE does not light up –
By keeping button FUNCTION (19) pressed one
of the four stroboscope functions may be acti-
vated:
1. Permanent stroboscope with white light
2. Permanent stroboscope with coloured light
3. Stroboscope with white light, music-controlled
4. Stroboscope with coloured light, music-con-
trolled
By keeping button FUNCTION pressed again,
the next stroboscope function is adjusted in each
case.
. To change the shade
chapter 6.2) in order to
chapter 6.1.1)
GB
15