Functional Description - IMG STAGELINE TANDEM-SCANNER LE-550DMX Manual De Instrucciones

Binary adjustment of the DIP switches is made,
i. e. the address is assigned according to the power
of two:
Switch 1 corresponds to 2
sponds to 2 1 (= 2), switch 3 corresponds to 2
(= 4), etc. The addresses are adjusted by "addition"
of the switches, e. g. 4 + 16 + 32 = address 52. For
this purpose, set the switches 3, 5, and 6 to "ON"
2 4 5
(2 + 2 + 2 ). The highest value to be adjusted for
"Dipswitch A" is address 123.
Adjusting examples:
If channels 1 to 5 of the controller are provided for
control, address 1 must be adjusted with the DIP
switches A and address 4 with the DIP switches B
on the light effect unit.
O N
1 2 3 4 5 6 7 8
1 2 4 8 16 32 64
Dipswitch A
Address 1 for "Dipswitch A", address 4 for "Dipswitch B"
If channels 6 to 10 of the controller are provided for
control, address 6 must be adjusted with the DIP
switches A and address 9 with the DIP switches B
on the light effect unit.
O N
1 2 3 4 5 6 7 8
1 2 4 8 16 32 64
Dipswitch A
Address 6 for "Dipswitch A", address 9 for "Dipswitch B"
It can be seen that for controlling the functions of
part B of the unit, the address on "Dipswitch B"
must always be adjusted 3 channels further than on
"Dipswitch A". If "Dipswitch B" has the same
address as "Dipswitch A", part B of the unit behaves
like part A of the unit.
3) DIP switch 8 inverts the sense of mirror rotation. If
this switch is set to "ON", the mirror turns to the left
instead of turning to the right, and vice versa. Thus,
it is possible to realize synchronous movement of
the connected scanners in opposite directions.
However, in case of control via DMX, only switch
8 of "Dipswitch A" must be set to "ON".
O N
1 2 3 4 5 6 7 8
Dipswitch A
Reversing the sense of mirror rotation
Note: Restart the scanner after each modification of
the DIP switch adjustments, i. e. switch the
scanner off, then switch it on again.

6.2.1 Functional description

Channel 1 (part A of the unit)
0 – 8: lamp off after 20 seconds
9 – 16: no gobo (blackout)
17 – 33: gobo round, white
0
(= 1), switch 2 corre-
2
O N
1 2 3 4 5 6 7 8
1 2 4 8 16 32 64
Dipswitch B
O N
1 2 3 4 5 6 7 8
1 2 4 8 16 32 64
Dipswitch B
O N
1 2 3 4 5 6 7 8
Dipswitch B
34 – 50: gobo round, red
51 – 67: gobo round, blue
68 – 84: gobo round, yellow
85 – 101: white tunnel
102 – 118: seven arcs, orange
119 – 135: blossom, magenta
136 – 152: seven-leaf clover, green
153 – 169: light beams, red and blue
170 – 186: pentagonal star, turquoise
187 – 203: flower, yellow
204 – 220: four-colour tunnel
221 – 237: eight stars, blue
238 – 255: rapid alternation of gobos
Channel 2 (part A of the unit)
0 – 32: lamp off after 20 seconds
33 – 255: lamp on
Channel 3
0 – 112: clockwise movement of the mirror
(0 = max. speed/112 = min. speed)
113 – 142: the mirror does not move
143 – 255: counterclockwise movement of the
mirror
(143 = min. speed/255 = max. speed)
Channel 4 (part B of the unit)
0 – 8: lamp off after 20 seconds
9 – 16: no gobo (blackout)
17 – 33: gobo round, white
34 – 50: gobo round, red
51 – 67: gobo round, blue
68 – 84: gobo round, yellow
85 – 101: white tunnel
102 – 118: seven arcs, orange
119 – 135: blossom, magenta
136 – 152: seven-leaf clover, green
153 – 169: light beams, red and blue
170 – 186: pentagonal star, turquoise
187 – 203: flower, yellow
204 – 220: four-colour tunnel
221 – 237: eight stars, blue
238 – 255: rapid alternation of gobos
Channel 5 (part B of the unit)
0 – 32: lamp off after 20 seconds
33 – 255: lamp on
7 Specifications
Power supply: . . . . . . 230 V~/50 Hz
Power consumption: . 320 VA
Lamps: . . . . . . . . . . . 2 x halogen lamp
Dimensions: . . . . . . . 556 x 145 x 184 mm (without
Weight: . . . . . . . . . . . 10.5 kg
According to the manufacturer.
Subject to technical change.
(15 V/150 W),
lamp base GZ 6.35
mounting brackets)
GB
9