Music Control - IMG STAGELINE TANDEM-SCANNER LE-550DMX Manual De Instrucciones

2) When replacing a lamp, carefully remove the old
GB
lamp from the lamp support and pull off the lamp-
holder.
3) Place the lampholder on the pin base of the new
lamp and carefully insert the lamp into the lamp
support.
4) Tightly close the cover of the lamp compartment
with the two screws.
5 Mounting
Use two supports for projectors or two sturdy mounting
screws to fix the unit via the two mounting brackets (5)
to the desired location (crossbar of a lighting stand or
horizontal T-bar). Alternatively, the unit can be sus-
pended from a single mounting bracket. In this case,
fix one of the two mounting brackets to the threaded
bolts (8) in the centre of the unit.
For aligning the unit, release the setscrews (6),
adjust the desired inclination of the unit and retighten
the setscrews.
Important!
To prevent heat accumulation within the unit, the
mounting location must be selected in such a way
that a sufficient air circulation is ensured during op-
eration. The air vents of the housing must not be
covered (e. g. by curtains, etc.).
6 Operation
Connect the supplied mains cable with cold appliance
inline jack to the cold appliance chassis plug (4), then
connect the mains plug to a socket (230 V~/50 Hz).
The unit is switched on as soon as it is connected to
the power supply. After switching on, the mirror is
placed in a defined starting position and the control is
reset. Then the unit is ready for operation. For switch-
ing off the unit, disconnect the mains plug.
For a more convenient operation, it is recommend-
ed to connect the unit to a mains socket which can be
switched on and off via a light switch.

6.1 Music control

For controlling the scanner via the integrated micro-
phone, set all 8 DIP switches of "Dipswitch A" down-
wards to the OFF position. Switch 3 of "Dipswitch B" is
set to "ON", set all other switches to the OFF position.
Adjust the desired volume on the music system in
such a way that the moving light beams reproduce the
dynamic efficiency of the music in an optimum way.
6.1.1 Interconnecting several scanners
Several scanners can be interconnected in order to
control all other slave units to the same rhythm via the
microphone of the master unit. Up to 16 slave units
can be controlled via a master unit.
1) Set the DIP switches on the master unit as de-
scribed in chapter 6.1.
8
O N
1 2 3 4 5 6 7 8
Dipswitch A
Master with activated output for slave control
2) Set the DIP switches on all slave units as shown
below (fig. 4).
O N
1 2 3 4 5 6 7 8
Dipswitch A
Slave, microphone control via master
For slave operation with reversed sense of mirror
rotation, additionally set both DIP switches 8 to
"ON":
O N
1 2 3 4 5 6 7 8
Dipswitch A
Slave inverted, microphone control via master
3) Connect the output (2) of the master unit to the
input (1) of the first slave unit via an XLR cable.
4) Connect the output of the first slave unit to the input
of the second slave unit, etc.
Note: Restart the scanner after each modification of
the DIP switch adjustments, i. e. switch the
scanner off, then switch it on again.
6.2 Control via a light control unit
The light effect unit LE-550DMX is equipped with five
DMX channels which can be individually controlled via
a DMX512 controller:
1. Channel 1 for triggering the colour/pattern disk
(gobos), part A of the unit
2. Channel 2 for for switching the lamp on and off, part
A of the unit
3. Channel 3 for controlling the sense of rotation and
the rotating speed of the mirror
4. Channel 4 for triggering the colour/pattern disk
(gobos), part B of the unit
5. Channel 5 for switching the lamp on and off, part B
of the unit
1) Connect the scanner to the DMX512 controller via
the input (1). Another DMX512 compatible light
effect unit can be connected via the output (2).
2) Adjust the DIP switches of "Dipswitch A" to the
address corresponding to the channel of the
DMX512 controller which is provided for controlling
channel 1 of the light effect unit, and adjust the DIP
switches of "Dipswitch B" to the address corre-
sponding to the channel of the DMX512 controller
which is provided for controlling channel 4 of the
light effect unit.
O N
1 2 3 4 5 6 7 8
Dipswitch B
O N
1 2 3 4 5 6 7 8
Dipswitch B
O N
1 2 3 4 5 6 7 8
Dipswitch B