Mitsubishi Electric Mr. Slim PCA-RP50KAQ Para El Instalador página 10

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 54
TEMP.
ON/OFF
MENU
ON/OFF
BACK
MONITOR/SET
DAY
CHECK
PAR-21MAA
CLOCK
OPERATION
CLEAR
Fig. 6-8
CHECK
ON/OFF
TEMP
FAN
AUTO STOP
MODE
VANE
AUTO START
CHECK
LOUVER
h
TEST RUN
min
SET
RESET
CLOCK
Fig. 6-9
Function table
Select unit number 00
Mode
Power failure automatic recovery
Indoor temperature detecting
LOSSNAY connectivity
Power voltage
Mode number
Setting number
Refrigerant address
Unit number
FILTER
TEST
CHECK
CHECK
CHECK
CHECK
Settings
Not available
Available
Indoor unit operating average
Set by indoor unit's remote controller
Remote controller's internal sensor
Not Supported
Supported (indoor unit is not equipped with outdoor-air intake)
Supported (indoor unit is equipped with outdoor-air intake)
240 V
220 V, 230 V
Changing the power voltage setting
• Be sure to change the power voltage setting depending on the voltage used.
Go to the function setting mode.
Switch OFF the remote controller.
Press the FILTER
and TEST RUN
them for at least 2 seconds. FUNCTION will start to blink.
Use the
buttons to set the refrigerant address ( ) to 00.
Press
button and [--] will start to blink in the unit number ( ) display.
Use the
buttons to set the unit number ( ) to 00.
Press the MODE button
to designate the refrigerant address/unit number. [--]
will blink in the mode number ( ) display momentarily.
Press the
buttons to set the mode number ( ) to 04.
Press the
button and the current set setting number ( ) will blink.
Use the
button to switch the setting number in response to the power supply
voltage to be used.
Power supply voltage
240 V
: setting number = 1
220 V, 230 V : setting number = 2
Press the MODE button
and mode and the setting number ( ) and ( ) will
Press the FILTER
and TEST RUN
seconds. The function selection screen will disappear momentarily and the air
conditioner OFF display will appear.
Changing the power voltage setting
• Be sure to change the power voltage setting depending on the voltage used.
Going to the function select mode
CHECK
Press the
button
twice continuously.
(Start this operation from the status of remote controller display turned off.)
CHECK
is lighted and "00" blinks.
Press the
temp button
once to set "50". Direct the wireless remote control-
ler toward the receiver of the indoor unit and press the
Setting the unit number
Press the
temp buttons
wireless remote controller toward the receiver of the indoor unit and press the
min
button
.
Selecting a mode
Enter 04 to change the power voltage setting using the
and
. Direct the wireless remote controller toward the receiver of the indoor
h
unit and press the
button
.
Current setting number:
1 = 1 beep (1 second)
2 = 2 beeps (1 second each)
3 = 3 beeps (1 second each)
Selecting the setting number
Use the
temp buttons
and
01 (240 V). Direct the wireless remote controller toward the sensor of the indoor
h
unit and press the
button
.
To select multiple functions continuously
Repeat steps
and
to change multiple function settings continuously.
Complete function selection
Direct the wireless remote controller toward the sensor of the indoor unit and
press the
button
.
Note: Whenever changes are made to the function settings after installation
or maintenance, be sure to record the changes with a mark in the "Setting"
column of the Function table.
Refer to the indoor unit operation manual.
Mode no.
01
02
03
04
buttons simultaneously and hold
buttons simultaneously for at least 2
h
button
.
and
to set the unit number "00". Direct the
temp buttons
to change the power voltage setting to
Setting no. Initial setting
setting
1
2
1
2
3
1
2
3
1
2

Publicidad

Tabla de contenido
loading

Tabla de contenido