Standard Accessories; Maintenance And Inspection - Metabo HPT DH24PG2 Instrucciones De Manejo

English

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○ Plastic case ................................................................ 1
○ Side handle ................................................................. 1
○ Depth gauge .............................................................. 1
○ Drill chuck holder (DH28PMY2 only) .......................... 1
Standard accessories are subject to change without notice.
APPLICATIONS
Rotation and hammering function
○ Drilling anchor holes
○ Drilling holes in concrete
○ Drilling holes in tile
Rotation only function
○ Drilling in steel or wood
(with optional accessories)
○ Tightening machine screws, wood screws
(with optional accessories)
Hammering only function
(DH24PH2, DH26PC2, DH28PCY2, DH28PMY2)
○ Light-duty chiselling of concrete, groove digging and
edging.
SPECIFICATIONS
The specifi cations of this machine are listed in the Table on
page 13.
NOTE
Due to metabo HPT's continuing program of research
and development, the specifi cations herein are subject
to change without prior notice.
MOUNTING AND OPERATION
Action
Inserting SDS-plus tools
Removing SDS-plus tools
Selecting rotation direction
Selecting the operating mode
Adjusting the drilling depth
Changing the chisel position
Removing the quick release chuck
(DH28PMY2)*
1
Inserting the quick release chuck
(DH28PMY2)
Inserting round shank applications
tools (DH28PMY2)
Switching on and off and setting
the speed
Locking-on the On / Off switch
Releasing the On / Off switch
Selecting accessories*
2
*1 If it is hard to pull out the drill chuck holder or the drill bit
holder, align the change lever with the
the lock grip.
*2 For detailed information regarding each tool, contact a
metabo HPT authorized service center.
LUBRICATION
This Rotary Hammer is of full air-tight construction to protect
against dust and to prevent lubricant leakage.
Therefore, this Rotary Hammer can be used without
lubrication for long periods. Replace the grease whenever
you change the carbon brush to maintain the service life.
Further use of the rotary hammer with lock off grease will
cause the machine to seize up reduce the service life.
CAUTION

MAINTENANCE AND INSPECTION

1. Inspecting the tools
2. Inspecting the mounting screws
3. Maintenance of the motor
4. Inspecting the carbon brushes
5. Replacing supply cord
Figure Page
1 14
2 14
CAUTION
3 14
4 14
5 14
6 14
NOTE
7 15
Due to metabo HPT's continuing program of research
and development, the specifi cations herein are subject to
8 15
change without prior notice.
9 15
10 15
11 15
12 15
– 16, 17
mark and turn
4
A special grease is used with this machine, therefore,
the normal performance of the machine may be badly
aff ected by use of other grease. Please be sure to let
one of our service agents undertake replacement of the
grease.
Since use of a dull tool will cause motor malfunctioning
and degraded effi ciency, replace the tool with new ones
or resharpen them without delay when abrasion is noted.
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
The motor unit winding is the very "heart" of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
For your continued safety and electrical shock protection,
carbon brush inspection and replacement on this
machine should ONLY be performed by a metabo HPT
Authorized Service Center.
If the replacement of the supply cord is necessary, this
has to be done by the manufacturer of this agent in order
to avoid a safety hazard.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.