Technical Data; Double Insulation; Additional Handle - Narex EVP 13 G-2H3 Instrucciones De Uso

Technical data

Impact drill
Type
Supply voltage
Power frequency
Power input
Speed under load
1st speed gear
2nd speed gear
Idle speed
1st speed gear
2nd speed gear
Number of impacts
1st speed gear
2nd speed gear
Speed pre-selection
Right-left turning
Extent of chuck dia.
Thread on spindle
Quick-tightening chuck Auto-Lock
Drilling dia. max
into steel
into aluminium
into wood
into concrete
Clamping neck dia.
Weight
Protection class
Controls
1 ............ Chuck with ring gear
2 ............ Spots on spindle
3 ............ Clamping neck
4 ............ Lever for impact shifting
5 ............ Air vents
6 ............ Latching pin
7 ............ Switch / controller
8 ............ Speed pre-selection wheel
9 ............ Alteration switch lever
10 .......... Gear-shifting lever

11 .......... Additional handle

12 .......... Stop bar
13 .......... Chuck hook
14 .......... Spanner
15 .......... Socket screw wrench
16 .......... Quick-tightening chuck
The displayed or described accessories need not be included in the delivery
package.

Double insulation

To ensure maximum safety of the user, our tools are designed and built to
satisfy applicable European standards (EN standards). Tools with double
insulation are marked by the international symbol of a double square.
These tools must not be grounded and a two-wire cable is sufficient to
supply them with power. Tools are shielded in accordance with EN 50114.
Use
The machine is intended drilling in wood, metal, ceramic and plastic.
Machines with electronic control and right/left rotation are also suitable
for screwing and thread cutting ( Only for soft screwdriving applications).
In addition, the machine is designed for impact drilling in brick, concrete
and stone as well as for drilling in wood, metal, ceramics and plastics.
Machines with electronic control and right/left rotation are also suitable for
screwing and thread-cutting.
The user alone is responsible for any liabilities caused by usage other than
intended.
EVP 13 G-2H3
230–240 V
50–60 Hz
760 W
0–600 min
-1
0–1 750 min
-1
0–1 100 min
-1
0–3 050 min
-1
0–22 000 min
-1
0–61 000 min
-1
ü
ü
1.5–13 mm
1/2"-20 UNF
û
13 mm
25 mm
45 mm
20 mm
43 mm
2.1 kg
II /
Commissioning and use
Any unauthorised use might cause damage to the tool. Therefore follow
these instructions:
- Always use sharp drill bits.
- Load the tool to avoid any significant reduction of speed or stoppage.
- Always change the speed gear when the machine is idle or at the
machine slow-down at low speed, in no case during the drilling or
when the machine is otherwise loaded.
Check whether the data on the name plate correspond with the actual
power supply voltage. Tools designed for 230 V may be connected also
to 220 / 240 V.
Additional handle
For safety reasons always use the additional handle (11), firmly mounted on
the clamping neck (3). The stop bar (12) can be used to adjust the drilling
depth. By rotating the handle the position of the addition al handle and the
depth stop can be modified.
Clamping of drill bits
Chuck with ring gear
Open the chuck to allow mounting of the tool. Mount the tool on. Mount
the tool on and, using the chuck hook (13) clamp in evenly.
Quick-tightening chuck
Open the chuck to allow mounting of the tool. Mount the tool on.
Tighten the quick-tightening chuck by your hand so strongly that a "click"
sound is heard clearly. Thus the chuck will be secured automatically.
This lock will release again if you turn the sleeve contra directionally to
remove the tool.
Be careful as the chuck gets hot:
In case of longer work tasks, especially in impact drilling, the chick
might get very hot. In this case you are recommended to wear
protective gloves.
Switching on and off
By pressing the switch button (7) the machine activates and releasing the
button stops it.
EVP 13 G-2A
230–240 V
50–60 Hz
760 W
0–600 min
-1
0–1 750 min
-1
0–1 100 min
-1
0–3 050 min
-1
0–22 000 min
-1
0–61 000 min
-1
ü
ü
1.5–13 mm
1/2"-20 UNF
ü
13 mm
25 mm
45 mm
20 mm
43 mm
2.2 kg
II /
English
15