Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
F = 0.0 kN
bar
F
= 7.57 ton
m
2
*
F = 0.00 ton
P
= 742 bar
m
3
*
P =
0 bar
The capacitive menu selection button may not work if touched using objects or when wear-
ing gloves, therefore always operate the button using a bare finger.
P
= 10762 psi
m
4
*
4.2) Choosing the "release mode"
P =
0 psi
The phase of discharging the oil into the tool's tank can be carried out in two different ways, de-
pending on the mode set in the menu:
5
*
F
= 67.4 kN
m
1
*
BATTERY
Release
F = 0.0 kN
BATTERY
mode
10
6
*
F
= 7.57 ton
14990
m
2
*
BATTERY
SMART
F = 0.00 ton
factory setting
B600ND
7
*
P
= 742 bar
20AR112
m
3
*
P =
0 bar
RESET
8
MANUAL
P
= 10762 psi
SW:S1J96902
m
4
*
bar
P =
0 psi
LED
9
ON
5
*
To change the "release mode", proceed as follows:
bar
BATTERY
Select screen 8 from the "main menu" (Ref. to section 4.1).
Hold finger on the button (7) until a confirmation "beep" is heard. The choice made is shown by
RESET
10
cursor position under the pictogram.
10
SW:S1J96902
6
*
max.
14990
4.3) Enabling/disabling the LED Worklights
11
BATTERY
B600ND
7
*
LED
20AR112
ON
12
LED
8
OFF
4.4) Return to original factory settings / firmware version
LED
9
Select screen 10 from the "main menu" (Ref. to section 4.1). To return the tool to its factory settings,
ON
hold finger on button (7) until a confirmation "beep" is heard.
RESET
10
SW:S1J96902
11
11
P
= 742 bar
m
3
*
P =
0 bar
To make a selected screen operational and appear at each start up of the
tool, operate the touch button for at least 3 seconds; a continuous beep
P
= 10762 psi
m
4
*
BEEP
P =
0 psi
will confirm the setting.
5
*
BATTERY
10
6
*
14990
Associated
B600ND
7
*
ERROR
20AR112
pictogram
8
15001
LED
9
ON
RESET
10
90°
SW:S1J96902
LED
max 90°
OFF
11
12
min.
BATTERY
BEEP
LED
OFF
The RESET screen also shows the firmware version of the control board.
BEEP
By releasing the operating button (3) the oil is returned in full to
F
= 67.4 kN
m
the tool reservoir only following automatic shut-off of the motor.
F
= 67.3 kN
p
During the return phase, pressing the buttons enables the ram
001
stroke to be interrupted at any point so as to be able to restart from
P
= 742 bar
m
this position in the next work phase, thus saving time and energy.
P
= 741 bar
p
002
LED
To return the oil to the tool reservoir it is necessary to press and
OFF
hold the release button (6).
003
During the return phase, by releasing the button it is possible for
the ram stroke to be interrupted at any point so as to be able to
restart from this position in the next work phase, thus saving time
004
and energy.
F
= 67.4 kN
m
F
= 67.3 kN
p
(factory setting is LED ON)
P
= 742 bar
m
Select screen 9 from the "main menu" (Ref.
P
= 741 bar
LED
p
to section 4.1). To deactivate or reactivate
OFF
operation of the LED Worklights, hold the
LED
finger on button (7) until a confirmation
ON
"beep" is heard.
P
= 742 bar
n
P
= 742 bar
p
P
= 742 bar
n
OK
P =
P = 0 bar
F
= 67.4 kN
m
P
= 325 bar
P
= 547 bar
p
p
P
= 742 bar
F
= 67.3 kN
n
p
P =
0 bar
P
= 742 bar
m
Function
P
= 741 bar
p
P
= 742 bar
n
P
= 742 bar
Fm = 67.4 kN
p
OK
P
= 742 bar
P
= 742 bar
n
n
OK
OK
P = 0 bar
P =
F
= 134.3 kN
m
OK
P
= 742 bar
m
P
= 325 bar
P
= 547 bar
p
p
OK
Fm = 67.4 kN
OK
P
= 742 bar
n
OK
F
= 134.3 kN
m
OK
P
= 742 bar
m
OK
OK
BA
P = 0 bar
P =
P
= 325 bar
P
= 547
p
p
0 bar
Fm = 67.4 kN
OK
BA
P
= 742 bar
n
OK
BA
F
= 134.3 kN
m
OK
LED
ON
P
= 742 bar
m
OK
LED
OFF
0 bar
LED
ON
LED
OFF
0 b
S
R
S
Publicidad
Tabla de contenido
