Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
10
6
*
NOTE: To display the momentary force or pressure during
14990
the work cycle, select the appropriate display from the
menu (Ref. to section 4). When the operating button is
B600ND
released before the motor stops automatically, the display
7
*
20AR112
will show the peak force (Fp) or the peak pressure (Pp)
reached at that point.
To complete the cycle, press the operating button again until the motor stops automatically; the display
8
will show the maximum force or pressure reached followed by "OK" to confirm correct operation.
P
= 742 bar
The display "ERROR", combined with a beep and the LEDs flashing,
n
P =
indicates an incorrect crimping procedure caused by the work cycle
LED
9
ON
being interrupted before the control parameters (force/pressure) of the
tool are reached.
P
= 742 bar
n
This error appears when the pressure release button has been operated and the tool has already
P
= 742 bar
F
= 67.4 kN
p
reached a pressure >100 bar. In this case, repeat the compression by pressing and holding the op-
RESET
m
10
1
*
F = 0.0 kN
SW:S1J96902
erating button until the motor stops automatically.
P
= 742 bar
n
F
= 7.57 ton
m
2
2.4) Release of dies
*
OK
F = 0.00 ton
11
Once the motor has stopped automatically, release the operating button (3), the ram will return,
allowing access and release of the dies.
P
= 742 bar
m
3
*
P =
0 bar
P = 0 bar
The oil discharge to reservoir can also be performed in manual mode (Refer to § 4.2 for
12
further details).
P
= 10762 psi
m
4
*
P =
0 psi
2.5) LED Worklights
P
= 325 bar
p
Whilst the tool is in operation, the compression area is illuminated by four high luminosity LED
5
*
Worklights that switch off automatically at the end of the cycle.
BATTERY
10
6
The LED Worklights can be disabled by following the procedure described in section 4.3.
*
14990
F
= 67.4 kN
m
2.6) Head rotation
F
= 67.3 kN
B600ND
p
7
*
For ease of operation, the tool head can rotate through 180°, allowing the operator to work in the
20AR112
most comfortable position.
P
= 742 bar
m
P
= 741 bar
p
8
Do not attempt to rotate the head when the hydraulic circuit is pressurised.
2.7) Capacitive touch button for menu selection
LED
9
ON
This button is located under the display and allows selection of various
screens (Ref. to section 4); accessible only when the display is on.
RESET
Wearing gloves or using other objects may inhibit the operation of the
10
SW:S1J96902
button, therefore use a bare finger to apply only a light touch.
11
0 bar
LED
OFF
P =
0 bar
P
= 547 bar
p
Fm = 67.4 kN
OK
P
= 742 bar
n
OK
LED
F
= 134.3 kN
m
OFF
OK
P
= 742 bar
m
OK
F
= 67.4 kN
m
F
= 67.3 kN
p
P
= 742 bar
m
P
= 741 bar
p
BATTERY
BATTERY
P
= 742 bar
n
P =
0 bar
15001
P
= 742 bar
n
P
= 742 bar
p
P
= 742 bar
n
RESET
OK
SW:S1J96902
90°
P =
P = 0 bar
max 90°
P
= 325 bar
P
p
max.
Fm = 67.4 kN
F
= 67.4 kN
m
OK
F
= 67.3 kN
p
P
= 742 bar
P
= 742 bar
BATTERY
n
m
OK
P
= 741 bar
p
LED
ON
F
= 134.3 kN
m
OK
LED
OFF
P
= 742 bar
m
OK
BEEP
Fm = 67.4 kN
OK
P
= 742 bar
n
OK
F
= 134.3 kN
m
OK
ERROR
P
= 742 bar
m
OK
BATTERY
BATTERY
0 bar
= 547 bar
p
min.
LED
BATTERY
ON
LED
OFF
BEEP
8
001
002
15001
003
RESET
004
SW:S1J96902
90°
max 90°
max.
BATTERY
LED
OFF
BEEP
LED
ON
BEEP
Publicidad
Tabla de contenido
