Bosch GSR 9,6-2 Professional Manual Original página 14

OBJ_BUCH-585-006.book Page 14 Monday, October 10, 2016 11:07 AM
14 | English
Cordless Drill/Driver
Chuck clamping range
Drill spindle thread
Weight according to
EPTA-Procedure 01:2014
*depending on the battery pack being used
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards:
EN 60745-1, EN 60745-2-1, EN 60745-2-2, EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering and PT/ECS
Manufacturing
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Battery Charging
A battery that is new or has not been used for a longer period
does not develop its full capacity until after approx. 5 charg-
ing/discharging cycles.
To remove the battery 6 press the unlocking buttons 7 and
pull out the battery downwards. Do not exert any force.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal.
Changing the Tool (see figure A)
Hold the rear sleeve 3 of the keyless chuck 1 tight and turn the
front sleeve 2 in rotation direction , until the tool can be in-
serted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight and firmly
turn the front sleeve 2 in rotation direction  by hand.
The locking is released again to remove the tool when the
front sleeve 2 is turned in the opposite direction.
1 609 92A 35F | (10.10.16)
GSR 9,6-2 GSR 12-2
Professional Professional
mm 1–10
3/8"
kg 1.7 1.5–1.6*
Replacing the Drill Chuck
Removing the Securing Screw (see figure B)
The keyless chuck 1 is secured with a securing screw 13
against unintentional loosening from the drill spindle. Com-
pletely open the keyless chuck 1 and unscrew the securing
screw 13 in rotation direction . Please note that the se-
curing screw has a left-hand thread.
Removing the Drill Chuck (see figure C)
Clamp the short end of a hex key 14 into the keyless chuck 1.
Place the machine on a stable surface (e. g. a workbench).
Hold the machine firmly and loosen the keyless chuck 1 by
turning the hex key 14 in rotation direction . Loosen a tight-
seated keyless chuck by giving the long end of the hex key 14
a light blow. Remove the hex key from the keyless chuck and
completely unscrew the keyless chuck.
Mounting the Drill Chuck (see figure D)
The keyless chuck is mounted in reverse order.
The drill chuck must be tightened with a tightening
torque of approx. 17–22 Nm.
Screw the securing screw 13 in anti-clockwise direction into
the opened keyless chuck. Always use a new securing screw,
as the threads are covered with a thread-locking compound
that loses its effect after multiple usage.
Dust/Chip Extraction
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Operation
Starting Operation
To save energy, only switch the power tool on when using it.
GSR 14,4-2 GSR 18-2
Professional Professional
1–10 1–10
3/8" 3/8"
1.8
Bosch Power Tools
1–10
3/8"
2.0