Standard Accessories; Prior To Operation - HIKOKI C8FSHE Instrucciones De Manejo

SPECIFICATIONS
Max. Cutting
Capacity Bevel
Height × Width
Compound
Saw Blade Dimensions (oD × iD × Thickness)
Maximum kerf
Miter Cutting Angle
Bevel Cutting Angle
Compound Cutting Angle
Voltage (by areas)*
Power Input*
No-Load Speed
Machine Dimensions (Width × Depth × Height)
Weight (Net)**
Laser Marker
(Only Model C8FSHE)
* Be sure to check the nameplate on product as it is subject to change by areas.
When cutting the workpiece which has the dimension of "**" there might be some possibility of the lower end of the circular
saw to touch with the workpiece, even if the motor head is located at the lower limit position. Pay attention when cutting the
workpiece. For further details, refer to "PRACTICAL APPLICATIONS". Mount the auxiliary board on the fence surface (Refer
( ) the thickness of auxiliary board). Refer to "10. Cutting large workpieces" (Fig. 22, 23).
1. Minimum size of the workpiece.
All workpieces that can be clamped left or right from the saw blade with the supplied vise assembly.
Model C8FSHE • C8FSE: 245 × 90mm (length × width)
2. Maximum cutting depth.
Model C8FSHE • C8FSE: 65mm (Miter 0° × Bevel 0°)
** According to EPTA-Procedure 01/2014

STANDARD ACCESSORIES

○ 216 mm TCT Saw blade (mounted on tool) ...................1
○ Dust bag .......................................................................1
○ 10 mm Box wrench .......................................................1
○ Vise Assembly ..............................................................1
○ Holder ...........................................................................1
○ Side Handle ..................................................................1
○ Sub Fence (mounted on tool) ........................................1
○ Sub table ass'y ..............................................................2
Standard accessories are subject to change without notice.
APPLICATION
Cutting various types of aluminium sash and wood.
0°
Miter 45°
Left 45°
Right 5°
Bevel (Left) 45° + Miter 45°
Bevel (Right) 5° + Miter 45°
Bevel (Left) 0° – 45°
Bevel (Right) 0° – 5°
Maximum output
(Iambda)
Laser medium
19
65 mm × 312 mm
**75 mm × 262 mm with aux. board (30 mm)
65 mm × 220 mm
**75 mm × 185 mm with aux. board (20 mm)
45 mm × 312 mm
**50 mm × 252 mm with aux. board (30 mm)
60 mm × 312 mm
**70 mm × 252 mm with aux. board (30 mm)
45 mm × 220 mm
**50 mm × 170 mm with aux. board (30 mm)
60 mm × 220 mm
**70 mm × 170 mm with aux. board (30 mm)
216 mm × 30 mm × 2 mm
Right 0° – 57°, Left 0° – 45°
Right 0° – 5°, Left 0° – 48°
Miter (Right and Left) 0° – 45°
(110 V, 230 V)
C8FSHE • C8FSE: 5500 min
555 mm × 790 mm × 485 mm
16.7 kg (C8FSHE) / 16.4 kg (C8FSE)
Po<3 mW Class II Laser Product

PRIOR TO OPERATION

CAUTION
Make all necessary adjustments before inserting the
plug in the power source.
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
Do not use with direct current, or transformers such as
boosters. Doing so may result in damage or accidents.
2. Power switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the trigger switch
is in the ON position, the power tool will start operating
immediately, inviting serious accident.
3. Extention cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
English
2.7 mm
1050 W
–1
654 nm
Laser Diode