Rotary Hammer Safety Warnings - Makita HR5000 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Switch trigger
2 Change lever
3 For hammering only
4 For rotation with hammering
5 Clamp nut
6 Side handle
7 Side grip
8 Tool holder
SPECIFICATIONS
Model
Capacities
Carbide-tipped bit ..................................................................... 50 mm
Core bit
Concrete .............................................................................. 150 mm
Hume pipe ........................................................................... 255 mm
–1
No load speed (min ) ................................................................. 260
Blows per minute ......................................................................... 2,100
Overall length .............................................................................. 476 mm
Net weight .................................................................................... 9.9 kg
Safety class ..................................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for hammer drilling in brick, concrete
and stone as well as for chiselling work.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future refer-
ence.

ROTARY HAMMER SAFETY WARNINGS

1. Wear ear protectors. Exposure to noise can cause
hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Explanation of general view
9 Tool retainer
10 Blow-out bulb
11 Core bit
12 Adapter
13 Center bit
14 Rod
15 Commutator
16 Insulating tip
4.
5.
ENE044-1
6.
ENF002-1
7.
8.
GEA010-1
9.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
12. Do not point the tool at any one in the area when
13. Do not touch the bit or parts close to the bit
GEB007-7
14. Some material contains chemicals which may be
SAVE THESE INSTRUCTIONS.
17 Carbon brush
18 Hex wrench
19 Rear cover
20 Screwdriver
21 Brush holder cap
22 Lock nut wrench
23 Crank cap
24 Hammer grease
HR5000
/II
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
Be sure the bit is secured in place before opera-
tion.
Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
Hold the tool firmly with both hands.
only when hand-held.
operating. The bit could fly out and injure some-
one seriously.
immediately after operation; they may be
extremely hot and could burn your skin.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
HR5000K
50 mm
150 mm
255 mm
260
2,100
503 mm
10.2 kg
/II
5