Safety Instructions For Maintenance; Assembly - McCulloch M40-120 CLASSIC Manual De Usuario

• Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry.
• If you spill fuel on your clothing, change clothing
immediately.
• Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use soap and water to
remove the fuel.
• Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
• Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
• Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
• Do not smoke near the fuel or the engine.
WARNING: Read the warning instructions
that follow before you use the product.
• The exhaust fumes from the engine contain carbon
monoxide, an odourless, poisonous and very
dangerous gas. Do not start the engine indoors or in
closed spaces.
• Before you do the maintenance on the product, stop
the engine and remove the ignition cable from the
spark plug.
• Use protective gloves when you do maintenance on
the cutting equipment. The blade is very sharp and
cuts can easily occur.
To assemble the handle
Lower handle section
1. Put the pins at the bottom of the lower handle into
the holes as given in the illustration. Align the screw
holes and attach the screws, washers and knobs.
(Fig. 18 )
Upper handle section
1. Align the holes in the handlebar with the holes in the
lower handle and attach the screws, washers and
knobs. On the right side also attach the loop for the
starter rope. Tighten the knobs fully.(Fig. 19 )
2. Pull the starter rope handle and put the starter rope
around the loop for the starter rope.(Fig. 20 )
3. Use the straps to attach the cables to the handle.
(Fig. 21 )
Note: Make sure that the tension in the cables is not
too high.
8

Safety instructions for maintenance

Assembly

• Do not put warm objects near the fuel or the engine.
• Do not add the fuel when the engine is on.
• Make sure that the engine is cool before you refuel.
• Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
• Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
• Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
• Move the product a minimum of 3 m (10 ft) from the
position where you filled the tank before a start.
• Do not put too much fuel in the fuel tank.
• Accessories and changes to the product that are not
approved by the manufacturer, can cause serious
injury or death. Do not change the product. Always
use accessories that are approved by the
manufacturer.
• If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
• Only do the maintenance as given in this owner's
manual. All other servicing must be done by an
approved McCulloch service agent.
• Let an approved McCulloch service agent do
servicing on the product regularly.
• Replace damaged, worn or broken parts.
To assemble the grass catcher
1. Put the grass catcher frame into the fabric grass
bag. Make sure that the handle on the grass catcher
frame is on top of the grass bag.
2. Attach the grass bag to the grass catcher frame with
the clips found on the fabric bag edge.(Fig. 22 )
3. Lift the rear cover.
4. Attach the grass catcher to the top edge of the
chassis.
5. Put the lower part of the grass catcher into the grass
discharge channel.
To assemble the mulch plug
A mulch kit is available as an optional accessory for
selected models only. Models M51-150WR CLASSIC,
M53-150WR CLASSIC come with the mulch kit
supplied. Models M40-120 CLASSIC, M40-125
CLASSIC+ can not be used with a mulch kit.
1. Lift up the rear cover and remove the grass catcher.
348 - 003 - 04.10.2017