Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Stand-Alone Mode
Auto Mode
•
Press <MENU> until
•
Press <ENTER> to confirm your selection.
•
Use <UP> or <DOWN> to select the desired program (
•
Press <ENTER> to confirm your selection.
•
Set the speed of built-in programs via <UP> or <DOWN> (
•
Press <MODE> to confirm your selection.
Preset Colours
This device has pre-programmed static colours.
•
Press <MENU> until
•
Press <ENTER> to confirm your selection.
•
Use <UP> or <DOWN> to select the desired program (
•
Press <ENTER> to confirm your selection.
Custom Static Colours
This device allows you to create custom static colours.
•
Press <MENU> until
•
Press <ENTER> to confirm your selection.
•
Use <UP> or <DOWN> to scroll through the options:
o
o
o
•
Press <ENTER> to select the desired sub-menu and use <UP> or <DOWN> to change the value.
•
Press <ENTER> to confirm the setting.
•
Press <ENTER> again to exit the menu.
Dimmer speed setting
•
Press <MENU> until
•
Press <ENTER> to confirm your selection.
•
Use <UP> or <DOWN> to select the desired dimmer speed (
•
Press <ENTER> to confirm your selection.
DMX Mode
This mode allows you to control the fixture by any universal DMX controller.
•
All DMX-controlled devices need a digital start address so that the correct device responds to the
signals. This digital start address is the channel number from which the device starts to "listen"
to the DMX controller. The same starting address can be used for a whole group of devices or an
individual address can be set for every device.
•
When all devices have the same address, all the units will "listen" to the control signal on one
particular channel. In other words: changing the settings of one channel will affect all devices
simultaneously. If you set individual addresses, each device will "listen" to a separate channel
number. Changing the settings of one channel will only affect the device in question.
•
In case of the 2-channel VDPLP3601VW, you will have to set the start address of the first unit
to 1 (CH1~2), the second unit to 3 (1 + 2) (CH3~4), the third to 5 (3 + 2) (CH5~6), and so on.
•
In case of the 3-channel VDPLP3601VW, you will have to set the start address of the first unit
to 1 (CH1~3), the second unit to 4 (1 + 3) (CH4~6), the third to 7 (4 + 3) (CH7~9), and so on.
•
In case of the 7-channel VDPLP3601VW, you will have to set the start address of the first unit
to 1 (CH1~7), the second unit to 8 (1 + 7) (CH8~14), the third to 15 (8 + 7) (CH15~21), and so
on.
•
Press <MENU> until
•
Press <ENTER> to confirm your selection.
•
Use <UP> or <DOWN> to set the number of DMX channels (
•
Press <MENU> until
•
Press <ENTER> to confirm your selection.
•
Use <UP> or <DOWN> to select the desired DMX starting address (
12.01.2011
VDPLP3601VW
is displayed.
is displayed.
is displayed.
... = warm white intensity (
... = cold white (
...) intensity (
... = strobe speed (
is displayed.
is displayed.
is displayed.
~
~
~
, from 0 to 100%)
~
(off) ~
(max.))
6
).
~
)
)
.
, from 0 to 100%)
~
)
,
,
or
)
~
).
©Velleman nv
.
Publicidad
Tabla de contenido
