Know Your Product; Operation; Prior To Initial Operation - SPARKY HeavyDuty X 85CES Plus Instrucciones De Uso

▪ Always keep the cord away from the working
area of the power tool.
▪ Never use the machine with a damaged ca-
ble. Do not touch the damaged cable and pull
the mains plug when the cable is damaged
while operating. Damaged cables increase
the risk of electric shock.
▪ Do not use blunt or damaged router bits. Blunt
or damaged router bits cause increased fric-
tion, can become jammed and lead to imbal-
ance.
▪ The tool must be used only for its prescribed
purpose. Any use other than those mentioned
in this Manual will be considered a case of
misuse. The user and not the manufacturer
shall be liable for any damage or injury result-
ing from such cases of misuse.
▪ To use this tool properly, you must observe
the safety regulations, the assembly instruc-
tions and the operating instructions found in
this Manual. All persons who use and service
the machine have to be acquainted with this
Manual and must be informed about its poten-
tial hazards. Children and frail people must not
use this tool. Children should be supervised
at all times if they are in the area in which the
tool is being used. It is also imperative that
you observe the accident prevention regula-
tions in force in your area. The same applies
for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
▪ Power tools must not be used outdoors in
rainy weather, or in moist environment (after
rain) or in close vicinity with easily flammable
liquids and gases. The working place should
be well lit.

Know your product

Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. ON/OFF switch
2. Cutting (shaping) depth guide
3. Knee vertical position fixing lever
4. Grip handles
5. Screw for tightening the electric motor
to the knee
6
EN
6. Three-level position support
7. Parallel guide ruler
8. Base plate
9. Spindle
10. Parallel guide
11. Screws for securing the parallel guide
12. Vertical guides
13. Cutting (shaping) depth reading ruler
14. Electronic regulator of rotation speed
15. Adapter for vacuum cleaner
16. Spindle lock

Operation

These power tools are supplied from single-
phase alternating current mains only. They
are double insulated according to EN 60745-1,
IEC 60745 and can be connected to grounded
or not grounded sockets. This power tool is radio
suppressed in compliance with EMC Directive.
The routers are power tools, designed for rout-
ing groove, roundover, cone, chamfering, profile
edges and openings in wood, wooden planes
and plastics, by means of straight and profile
router bits.

PRIOR TO INITIAL OPERATION

▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with the technical data of the tool.
▪ Always check the position of ON/OFF switch.
The router must be connected and discon-
nected to the power supply socket only when
this switch is in OFF position.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
▪ Before starting to operate, ensure the router
bit being used has the correct shank size
matching the inserted collet and the maxi-
mum number of revolutions of the used tool.
▪ Make sure if the router bit is secured in the
collet.
WARNING: Always switch off and
unplug the power tool prior to any adjustment,
servicing or maintenance.
The router is designated to operate with router
bits with shank diameter 6 and 8 mm. The maxi-
mum diameter of the router bit active part shall
not exceed Ø30. The high speed requires usage
of high-quality router bits in order to guarantee
X 85CES Plus ● X 110CES Plus