Proper Use; Technical Data - EINHELL TC-MS 216 Manual De Instrucciones Original

3. Proper use

The crosscut and miter saw is designed for cross-
cutting wood and wood-type materials which are
appropriate for the machine's size. The saw is not
designed for cutting fi rewood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades. It is prohibited to use any type of
cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut inju-
ries).
•
Kick-back of workpieces and parts of workpi-
eces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.
Anl_TC_MS_216_SPK9.indb 21 Anl_TC_MS_216_SPK9.indb 21
GB

4. Technical data

AC motor ..................................220-240V ~ 50Hz
Power .....................S1 1400 W / S6 25% 1600 W
Idling speed n ....................................5000 min
0
Carbide saw blade ............ø 216 x ø 30 x 2.4 mm
Maximum tooth pitch ............................... 2.8 mm
Number of teeth .............................................. 48
Weight ........................................................7.1 kg
Pivoting range ............................. -47° / 0° / +47°
Miter cut ................................. 0° to 45° to the left
Saw width at 90° .................... max. 120 x 60 mm
Saw width at 45° ...................... max. 80 x 60 mm
Saw width at 2 x 45°
(double miter cut) ..................... max. 80 x 45 mm
Protection class: ........................................... II/
Minimum workpiece size: Only ever cut workpie-
ces which are big enough to clamp securely with
the clamping device – minimum length 160 mm.
Operating mode S6 25%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 25% of the cycle at the
specifi ed rating and must then be allowed to idle
for 75% of the cycle.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
L sound pressure level ..................... 95,5 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ..................... 108,5 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
- 21 -
-1
15.03.2019 13:55:30 15.03.2019 13:55:30