Know Your Product; Operation; Brush Replacement - SPARKY GUR 12 Instrucciones De Uso

impORtant inFORmatiOn FOR
REcHaRGinG HOt BattERiES
When using your cordless angle drill/driver continuously,
the batteries in your battery pack will become hot. You
should let a hot battery pack cool down for approximately
30 minutes before attempting to recharge. When the bat-
tery pack becomes discharged and is hot, the red light
on the charger will flash. When the battery pack cools
down, the red light will glow continuously to indicate fast
charging mode, 1-hour charge time.
nOtE. This will occur when continuous use of your tool
causes the battery pack to become hot. It does not occur
under normal conditions.
VII - Know your product
1. ON/OFF switch
2. Forward/reverse switch
3. Bit holder
4. Battery
5. Charger
6. LED charge indicator
VIII - Operation
SWitcH OpERatiOn
1. To turn the machine on, squeeze the trigger switch. To
turn the machine off, release the trigger switch.
2. Your power tool is equipped with a brake. The tool will
stop as soon as the trigger switch is fully released.
The farther you squeeze the trigger, the faster the tool
will operate.
inSERtinG anD REmOvinG BitS
(GUR 12)
Always follow the below described procedure to install
driver bit. (Fig. 4A)
1. Pull the sleeve forward.
2. Insert the bit into the hexagonal recess in the anvil.
3. Release the sleeve and it returns to its original posi-
tion to secure the bit.
WaRning: If the sleeve does not return to its
original position, then the bit is not installed properly.
inStallinG / REmOvinG tHE impact
SOckEt (GUR 12S)
1. Align the hole in the side of the socket; put it onto the
anvil of the tool until it locks into place. (Fig. 4B)
2. Depress the detent pin through the hole, and pull the
socket off.
To remove the bit / socket, perform the above mentioned
in reverse order.
Original instructions
WaRning: When using the hex adapter and
any of the hex bits supplied with the machine, if the
guide sleeve does not return to its original position,
then the bit is not installed properly.
WaRning: Always set switch to off position
when inserting or removing bits.
FORWaRD / REvERSE SWitcH
The bit rotates clockwise (viewed from the rear) by
pushing the R-side of the push button. The L-side of the
push button is pushed to turn the bit counter-clockwise.
(Fig. 5)
WaRning: The push button can not be
switched while the drill is turning. To switch the push
button, stop the machine and then set the push button.
tiGHtEninG anD lOOSEninG ScREWS
Install the bit that matches the screw, line up the bit in the
grooves of the head of the screw then tighten it.
Push the impact driver just enough to keep the bit fitting
the head of the screw.
WaRning: Over tightening can result in the
screw breaking or damage to the end of the driver bit.
▪ Applying the impact driver for too long tightens the
screw too much and can break it.
▪ Tightening a screw with the impact driver at an angle
to that screw can damage the head of the screw and
the proper force will not be transmitted to the screw.

BRUSH REplacEmEnt

1. Completely unscrew the cap (Fig. 6, A)
2. Next pull the brush out from the brush holder.
3. Worn brushes should be replaced in the same holder
and position as removed.
4. Re-fasten the cap.
5. Check that the tool can operate. Before use, allow it to
run for a few minutes to enable the brushes to settle.
OpERatinG tHE DRill
1. Resting the unit after
After continuous operation, leave the power tool for
15 minutes or so to rest when replacing the battery.
The temperature of the motor, switch, etc., will rise if
operation is started again immediately after battery
replacement, eventually resulting in burnout.
2. Place the point of the driver bit in the screw head.
Keep the tool pointed straight at the screw.
3. Apply forward pressure to the tool to prevent the bit
from slipping off the screw.
4. Turn the power tool on to start operation.
continuous

operation.

7
EN