Important Safety Instructions - Makita ML142 Manual De Instrucciones

ENGLISH
1. Battery
2. Reflector (ML142 only)
3. Fluorescent Tube
4. Lamp Cover
5. Screw Ring
SPECIFICATIONS
Model
Power Source
Fluorescent Tube
Dimensions
(L x W x H)
Net Weight
• Due to our ongoing research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:
When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric
shock, and personal injury. Some basic safety precautions are as follows:
READ ALL INSTRUCTIONS.
1. Read this instruction manual and the charger instruction manual carefully before use.
2. This Job site light is not waterproof. Do not use it in damp or wet locations. Do not expose it to rain or snow.
Do not wash it in water.
3. A short-circuit can cause a large current flow, overheating, possible burns and even damage.
(1) Do not touch the inside of the Job site light with tweezers, metal tools, etc.
(2) Do not touch the battery terminals with any conductive materials.
(3) Avoid storing the battery in a container with any metal objects such as nails, coins, etc.
4. Never expose the battery to flames, fire or significant heat. Breakage may cause release of dangerous
material.
5. If battery chemicals get into your eyes, rinse them out with water and seek medical attention right away. It
may result in loss of your eyesight.
6. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
7. Be careful not to drop, shake or strike the battery.
8. When the tool is not in use, always switch off and remove the battery from the tool.
9. Do not store the tool and battery in locations where the temperature may reach or exceed 50°C (122°F).
10. Do not give the tool a shock by dropping, striking, etc.
11. Do not expose the light to eyes continuously. It may hurt them.
12. Do not cover or clog the lit tool with cloth or carton, etc. It may create a risk of starting a fire.
13. Switch off the light immediately when the lamp light is low. If you leave the lamp switched on, the battery
capacity may decrease.
14. Do not disassemble the charger or battery; take it to a qualified serviceman when service or repair is required.
Incorrect reassembly may result in a risk of electric shock or fire.
15. If any problem develops, consult your nearest Makita Service Center or dealer. Maintenance or repairs should
be carried out by Makita Authorized Service Centers to maintain product safety and reliability.
16. If you notice that the tool is hot or is not functioning correctly, consult your nearest Makita Service Center or
dealer.
6. Switch
7. Strap Hook (ML142 only)
8. Strap (ML142 only)
9. Loosen
10. Tighten
ML142
D.C. 14.4 V
Compact FL13 W
347 mm x 94 mm x 116 mm
(13-5/8" x 3-11/16" x 4-9/16")
0.35 kg (0.77 lbs)
Diagram Legend
ML143
D.C. 14.4 V
Compact FL13 W
Hook Deployed
411 mm x 94 mm x 116 mm
(16-1/4" x 3-11/16" x 4-9/16")
Hook Not Deployed
350 mm x 94 mm x 116 mm
(13-3/4" x 3-11/16" x 4-9/16")
0.37 kg (0.81 lbs)
11. Connecting Ring
12. Fluorescent Tube Cap
13. Rings for Strap Clip Attachment
14. Metal Strap Clip
15. Metal Hang Hook
(ML143/183 only)
ML183
D.C. 18 V
Compact FL13 W
Hook Deployed
411 mm x 95 mm x 129 mm
(16-1/4" x 3-3/4" x 5-1/8")
Hook Not Deployed
350 mm x 95 mm x 129 mm
(13-3/4" x 3-3/4" x 5-1/8")
0.37 kg (0.81 lbs)
3