Storage Of The Boat; Treatment And Storage; Guarantee Conditions; Boat Repairing - Gumotex RUBY Manual De Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 22
Technical equipment for WW 2:
Agile, open boats (slalom types), boats with decking are
more suitable; a life jacket with a minimum displacement of
7.5 kg
ATTENTION
Pay great attention to your choice of flotation life-jacket.
The flotation life-jacket should have a tag bearing details
of its flotation capabilities and safety certification.
5. Storage of the Boat – See Fig. 3
Remove the seats and transom prior to roll-up. Place all small
accessories to the small mesh bag. No sharp object may re-
main in the boat. Clean and dry the boat. Bleed air from all
chambers. The deflation may be sped up by rolling the boat
towards the valves. Once all air has bled, place the boat on an
even surface and roll up – refer to Fig. 3.
Lay the boat flat. Fold both side tubes lengthwise so they do
not project outside the contour of the bottom. Now roll the boat
from both ends to the center. Place the folded halves on top
of each other and tie with the compressing strap. Insert the
boat in the transport bag, add the seats, transom and small
accessories. Force the air out of the bag, roll the end of the
bag and tie it with buckles.

6. Treatment and Storage

The rubber surface coating of the boat is sensitive to oils, gas-
oline, toluene, acetone, kerosene and similar thinning agents.
Prior to storing a dirty boat, wash it down with warm soapy
water. Rinse the boat with fresh water after using the boat in
seawater. It is recommended to check the state of the inflation
valves and the safety relief valves.
If a valve is not air-tight, it is possible to unscrew the valve
body from the boat with the use of a special valvekey and cle-
an its membrane with a strong jet of water or compressed air.
Prior to storage, it is recommended to rub the surface of the
boat with an agent intended for the treatment of such surfaces,
which has cleaning properties, and which impregnates the ma-
terial to prevent further dirtying, or which is capable of forming
a protective UVfilter.
Never use agents containing silicon when treating your boat.
Store the clean and dry product in a dark dry place at a tem-
perature of (15 – 35) °C, at least 1.5 m from any radiant heat
source and out of the reach of rodents. During longterm sto-
rage, it is recommended to inflate the boat for 24 hours from
time to time to avoid fatiguing the fold lines.
It is also recommended to have the boat serviced by the ma-
nufacturer's authorized service station at least once every two
or three years.
Proper care and treatment of the boat will increase its service
life.

7. Guarantee Conditions

The guarantee period is 24 months and is calculated from the
date of sale.
The producer provides cost-free repairs or replacement of
faulty components for material faults or production faults.

8. Boat Repairing

You can easily repair a damaged boat yourselves by means of
the accompanying gluing set.
12
Gluing:
mark out the damaged area on the boat and choose an
appropriately sized patch;
the surfaces of both patch and place to be glued must be
clean, dry and without traces of old glue;
Degrease the patch and the damaged spot with acetone or
petrol;
spread a thin layer of glue on both surfaces to be glued and
repeat this step once the first layer has dried;
after the second layer has dried, press the patch firmly on
the damaged place, weigh down or use a rolling pin on
a flat surface.
For minor repairs (punctures), it is possible to re-inflate the
boat and continue using it after waiting for approx. 30 minutes;
after more serious repairs, you should wait for 24 hours before
using the repaired boat. Complicated repairs should be per-
formed by the manufacturer or at authorized service stations.
Guarantee repairs and post-guarantee repairs are provi-
ded by the manufacturer:
GUMOTEX, a. s.
Mládežnická 3062/3a
690 75 Břeclav
Czech Republic

9. Product Disposal Method

The product should be disposed of at municipal waste dispo-
sal sites.

10. Packaging Disposal Method

Cardboard – recycle as the indicated symbol directs.
PE-LD plastic wrap (low-density branched polyethylene) – re-
cycle as the indicated symbol directs.

11. Type Parameters Tag

Each boat is provided with its own Type Parameters Tag which
displays the most important technical parameters.
Please follow these values. Above all, do not overload the boat
and maintain the recommended maximum pressures in the air
chambers.
Drawing and legend

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido