REMS Cento Instrucciones De Servicio página 16

eng
Deburring of outside/inside of pipes (Fig. 4)
With the REMS REG 10 – 54 E (13) pipes of Ø 10 – 54 mm, Ø ½ – 2⅛" can be
deburred on the outside and inside. There is a bit holder on the back of the
cutting wheel shaft for driving the REMS REG 10 – 54 E. The pipes to be
deburred are pressed by hand against the REMS REG 10 – 54 E set into rota-
tion by the pipe cutting machine.
NOTICE NOTICE
Remove REMS REG 10 – 54 E (13) for cutting pipes. The bit holder is approved
only for REMS REG 10 – 54 E. Other tools with bit holder are not approved. only
3.4. Marking device (Fig. 10)
For marking the insertion depth for fi ttings on pipes. For REMS Cento, REMS
Akku-Cento 22 V.
4. Maintenance
Notwithstanding the maintenance described below, it is recommended to send
in the pipe cutting machine to an authorised REMS contract customer service
workshop for inspection and periodic testing of electrical devices at least once
a year. In Germany, such periodic testing of electrical devices should be
performed in accordance with DIN VDE 0701-0702 and also prescribed for
mobile electrical equipment according to the accident prevention rules DGUV,
regulation 3 "Electrical Systems and Equipment". In addition, the respective
national safety provisions, rules and regulations valid for the application site
must be considered and observed.
5. Behaviour in the event of faults
5.1. Fault: Pipe cutting machine stops during operation. The LED of the machine status check (18) lights red (REMS Akku-Cento 22 V).
Cause:
● Feeding pressure too high.
● Blunt/broken cutting wheel.
● Worn carbon brushes.
● Battery depleted or defective (REMS Akku-Cento 22 V).
● Unsuitable battery inserted (REMS Akku-Cento 22 V).
5.2. Fault: Pipe stops during cutting.
Cause:
● Pipe not round.
● Pipe not deburred on the outside.
● Rollers (3) soiled.
5.3. Fault: Pipe is not cut.
Cause:
● Unsuitable cutting wheel.
● Pipe not round.
● Pipe not deburred on the outside.
● Cutting wheel damaged.
5.4. Fault: Pipe not cut completely, stops.
Cause:
● Unsuitable cutting wheel.
● Pipe not running round.
● Feeding pressure too high.
5.5. Fault: Pipe cutting machine does not start.
Cause:
● Mains lead defective (REMS Cento, REMS Cento RF,
REMS DueCento).
● Battery depleted or defective (REMS Akku-Cento 22 V).
● Unsuitable battery inserted (REMS Akku-Cento 22 V).
● Pipe cutting machine defective.
● Worn carbon brushes.
● Feeding pressure too high.
5.6. Fault: Cutting wheel becomes blunt or breaks out after 1 or 2 cuts.
Cause:
● Cutting in a cutting notch in which the previous cutting wheel already
became blunt or was damaged.
● Unsuitable cutting wheel.
● Pipe material is unsuitable for cutting.
16
4.1. Maintenance
WARNING WARNING
Before service work, pull the mains plug or remove the battery!
Keep the rollers (3) of the pipe cutting machine and the roller insert (14) as well
as the cutting wheel (2) and cutting wheel holder clean. Clean the spindle (8)
and guides of the cutting wheel drive (1) from time to time and grease lightly
with machine oil. Clean heavily soiled metal parts with the REMS CleanM (Art.
No. 140119) cleaner, for example, and then protect against rust.
Clean plastic parts (e.g. housing) only with the REMS CleanM machine cleaner
(Art. No. 140119) or a mild soap and a damp cloth. Do not use household
cleaners. These often contain chemicals which can damage the plastic parts.
Never use petrol, turpentine, thinner or similar products to clean plastic parts.
Make sure that liquids never get inside the pipe cutting machine.
4.2. Inspection / Maintenance
WARNING WARNING
Before any repair work, pull the mains plug or remove the battery! This
work may only be performed by qualifi ed personnel.
The gear of REMS Cento, REMS Cento RF, REMS Akku-Cento 22 V and REMS
DueCento is maintenance-free. It runs in a life-long grease fi lling and therefore
needs no lubrication. The motor has carbon brushes. These are subject to wear
and must therefore by checked and changed by qualifi ed specialists or an
authorised REMS customer service workshop from time to time. Only use
original REMS carbon brushes. The carbon brushes of the DC motors wear in
cordless pipe cutting machines. These cannot be replaced; the DC motor must
be replaced. See also page 5. Behaviour in the event of faults.
Remedy:
● Reduce feeding pressure. Wait until the LED lights green (REMS Akku-Cento
22 V).
● Change cutting wheel.
● Have the carbon brushes or DC motor changed by qualifi ed personnel or an
authorised REMS customer service workshop.
● Charge the battery with the Li-Ion rapid charger or change the battery.
● Usable batteries, see 1.5.
Remedy:
● Reduce feeding pressure.
● Deburr pipe on the outside.
● Clean rollers with machine cleaner REMS CleanM (Art. No. 140119), then
protect against rust.
Remedy:
● Select and change cutting wheel according to the pipe to be cut.
● Reduce feeding pressure.
● Deburr pipe on the outside.
● Change cutting wheel.
Remedy:
● Select and change cutting wheel according to the pipe to be cut.
● Stop pipe cutting machine. Break off the pipe section completely by hand,
e.g. with a screwdriver.
● Reduce feeding pressure.
Remedy:
● Have the mains lead changed by qualifi ed personnel or an authorised
REMS customer service workshop.
● Charge the battery with the Li-Ion rapid charger or change the battery.
● Usable batteries, see 1.5.
● Have the pipe cutting machine inspected/repaired by an authorised REMS
customer service workshop.
● Have the carbon brushes or DC motor changed by qualifi ed personnel or an
authorised REMS customer service workshop.
● Reduce feeding pressure.
Remedy:
● Place the cutting wheel next to the notch with the remaining fragments.
● Select and change cutting wheel according to the pipe to be cut.
● Only use approved pipes, see 1.3.
eng
, REMS Akku-Cento 22 V , REMS Akku-Cento 22 V and REMS