Troubleshooting - Homelite VersaTool UT20811 Manual Del Operador

Tabla de contenido

Publicidad

TROUBLE SHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICING DEALER.
PROBLEM
Engine will not start:
Engine starts but will not acceler-
ate:
Engine starts but will only run at
high speed at half choke:
Engine does not reach full speed
and emits excessive smoke:
Engine starts, runs, and acceler-
ates but will not idle:
String will not advance when using
the EZ Line™ tap advance system:
Spool retainer hard to turn when
using EZ Line™ tap advance
system:
Grass wraps around driveshaft
housing and stringhead:
Oil drips from muffler:
C
A
12
POSSIBLE CAUSE
1. No spark.
2. No fuel.
3. Flooded engine.
4. Starter rope pulls harder now than when new.
Carburetor requires adjustment.
Carburetor requires adjustment.
1. Check oil fuel mixture.
2. Air filter dirty.
3. Carburetor requires adjustment.
4. Spark Arrestor Screen Dirty.
Carburetor requires adjustment.
1. String welded to itself.
2. Not enough string on spool.
3. String worn too short.
4. String tangled on spool.
5. Engine speed too slow.
Screw threads dirty or damaged.
1. Cutting tall grass at ground level.
2. Operating trimmer at part throttle.
1. Operating trimmer at part throttle
2. Check oil/fuel mixture.
3. Air filter dirty.
4. Carburetor requires adjustment.
Note: This engine complies with EPA (Environmental Protection Agency) and CARB
*
(California Air Resource Board) regulations which require exhaust emission control. As
a result, the carburetor adjustment needle(s) are equipped with plastic cap(s) that limit
the rotation from the original factory adjustment. If your unit exhibits specific performance
problem(s) where the Trouble Shooting Section recommends a needle adjustment and you
are at the limit of adjustment, the unit should be taken to a factory authorized service center
B
for repair.
SOLUTION
1. Check spark. Remove spark plug. Reattach the spark
plug cap and lay spark plug on metal cylinder. Pull the
starter rope and watch for spark at spark plug tip. If
there is no spark, repeat test with a new spark plug.
2. Push primer bulb until bulb is full of fuel. If bulb does
not fill, primary fuel delivery system is blocked.
Contact a servicing dealer. If primer bulb fills, engine
may be flooded (see next item).
3. Remove spark plug, turn trimmer so spark plug hole
is aimed at the ground. Move choke lever to "RUN"
and pull starter cord 10 to 15 times. This will clear
excess fuel from engine. Clean and reinstall spark
plug. Pull starter three times with choke lever at
"RUN". If engine does not start, move choke lever to
"CHOKE" and repeat normal starting procedure. If
engine still fails to start, repeat procedure with a new
spark plug.
4. Contact a servicing dealer.
*Turn "L" needle (A) counterclockwise 1/16 turn. If "L" low
needle (A) can not be turned counterclockwise, do not
force plastic limiter caps. Contact a servicing dealer.
*Turn "H" needle (B) counterclockwise 1/16 turn. If "H" high
needle (B) can not be turned counterclockwise, do not force
plastic limiter caps. Contact a servicing dealer.
1. Use fresh fuel and the correct 2-cycle oil mix.
2. Clean per instructions in Maintenance Section.
3. Turn "H" needle (B) clockwise 1/16 turn.
4. Contact a servicing dealer.
Turn idle speed screw (C) clockwise to increase idle speed.
1. Lubricate with silicone spray - use Homelite® string.
2. Install more string (see String Replacement).
3. Pull strings while alternately pressing down on and
releasing spool retainer.
4. Remove string from spool and rewind (see String Replace-
ment).
5. Advance string at full throttle.
Clean threads and lubricate with grease - if no improve-
ment, replace spool retainer.
1. Cut tall grass from the top down to prevent wrapping..
2. Operate trimmer at full throttle.
1. Operate trimmer at full throttle.
2. Use fresh fuel and the correct 2-cycle oil mix.
3. Clean per instruction in Maintenance Section.
4. Turn "H" (B) needle clockwise 1/16 turn.

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido