Flotec Easy Sump Manual Del Usuario página 2

Specifications and Safety
DESCRIPTION
This Easy Sump™ is designed for home sumps. Unit is
equipped with a 3-prong grounding-type power cord.
Shaded-pole motor is oil filled and sealed for cooler
running. Sleeve bearings on motor shaft never need
lubrication. Automatic reset thermal protection. Not
designed for use as a swimming pool drainer.
SPECIFICATIONS
Power supply required ...........................115V, 60 HZ.
Liquid Temp. Range ................32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ....15 Amps
Discharge:
Check Valve .......................1-1/4" slip / 1-1/2" slip
Hose ............................................................1-1/4"
NOTICE: Do not reduce size of discharge pipe or
hose below 1-1/4" diameter. If discharge is too
small, pump will overheat and fail prematurely.
NOTICE: This unit is not designed as a waterfall or
fountain pump, or for applications involving salt
water or brine! Use with waterfalls, fountains, salt
water or brine will void warranty.
Pump water only with this pump.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
Risk of electrical shock. Do not
handle or plug in pump or pump motor with wet
hands or when standing on wet or damp surface or
in water.
PERFORMANCE
TOTAL FEET (M) OF LIFT
Series HP (1.5m)
CAPACITY GALLONS(L)/HOUR
FPRP3250C 1/2
(12 113) (10 220) (7 571)
ELECTRICAL & SWITCH SPECIFICATIONS
Motor
Full Load
Series HP Amps
FPRP3250C 1/2 5.5
GENERAL SAFETY INFORMATION
Electrically powered sump pumps normally give
many years of trouble-free service when correctly
installed, maintained, and used. However, unusual
circumstances (interruption of power to the pump,
dirt/debris in the sump, flooding that exceeds the
pump's capacity, electrical or mechanical failure in
the pump, etc.) may prevent your pump from
functioning normally. To prevent possible water
For parts or assistance, call Flotec Customer Service at
5 10 15
(3m) (4.6m)
3200 2700 2000
Individual
Branch *Switch Setting
Circuit in inches (mm)
Req.(Amps) On
15 8"(203)
damage due to flooding, consult your retailer about a
secondary AC sump pump, a DC backup sump
pump, and/or a high water alarm. See the
"Troubleshooting Chart" in this manual for
information about common sump pump problems
and remedies. For more information, see your
retailer or call customer service at
1-800-365-6832.
1. Know the pump application, limitations, and
potential hazards.
2. Do not use this pump in water with fish present. If
any oil leaks out of the motor it can kill fish.
3. Disconnect power before servicing.
4. Release all pressure within system before
servicing any component.
5. Drain all water from system before servicing.
6. Secure discharge line before starting pump. An
unsecured discharge line will whip, possibly
causing personal injury and/or property damage.
7. Check hoses for weak or worn condition before
each use, making certain that all connections are
secure.
8. Periodically inspect sump, pump and system
components. Keep free of debris and foreign
objects. Perform routine maintenance as
required.
9. Provide means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
10. Personal Safety:
a. Do not plug in or otherwise handle with wet
hands or when standing on wet or damp
surface, or in water.
b. Wear safety glasses at all times when working
No flow
at height
with pumps.
shown
c. Keep work area clean, uncluttered and
below
properly lighted – replace all unused tools
24 Ft.
and equipment.
(7.3M)
d. Keep visitors at a safe distance from work
area.
e. Make workshop child-proof – with padlocks,
master switches, and by removing starter
keys.
11. When wiring an electrically driven pump, follow
Off
3.5"(89) all electrical and safety codes that apply.
12. This equipment is only for use on 115 volt
(single phase) and is equipped with an
approved 3-conductor cord and 3-prong,
grounding-type plug.
1-800-365-6832
2