Inglesina Zippy Evo Manual De Instrucciones página 31

HOOD
fig. 56 Insert the ends of the hood in the proper seats on
the sides of the transport seat and hook the buttons to the
structure.
fig. 57 To remove the hood, simply extract it.
The hood covering can be removed to allow its correct
maintenance.
fig. 58
Unhook the buttons (H1) positioned on both sides
of the hood articulated joints (H2).
fig. 59
Then, unhook both articulated joints (H2) from the
rods (H3) and extract the covering completely.
fig. 60
To reassemble the covering, insert both rods (H3) in
the proper guides on the internal lining.
fig. 61 Then, insert the rods (H3) in the proper seats
on both articulated joints (H2), until they are completely
hooked.
fig. 62 WARNING: the curved insertion part of the
articulated joints (H2) must always be positioned on the
front.
MUFF
fig. 63
Position the muff (R3) letting it pass under the
bumper bar.
fig. 64
Secure the central string (A1) by feeding it through
the ring (A2).
fig. 65 Fasten the 2 lower buttons (A3) to the
corresponding studs beneath the stroller platform.
fig. 66 Secure the 2 side strings (A4) around the handrail
by fastening the corresponding snap fasteners.
fig. 67 The muff can be wrapped around itself when
closing the stroller with the crotch cover mounted, by
hooking the central string (A1) to the corresponding lower
eyelet (A5).
fig. 68
The muff reverse may also be hooked in a suitable
position for protecting the child against cold weather.
fig. 69
The muff can be used either on the transport seat
facing the mum or street.
ADJUSTMENT OF THE FOOTREST PLATFORM
fig. 70 To lower the platform act on both levers (S5)
positioned on the lower part of the same and simultaneously
press it downwards.
fig. 71 To lift the platform just pull it upwards: It will block
automatically.
SAFETY BELTS
fig. 72
Verify that the safety belts are inserted in the
eyelets at the height of the shoulders or immediately above.
If the position is not correct, extract the belts from the first
pair of eyelets and reinsert them in the second one; always
use eyelets at the same height.
fig. 73 Make sure that the back strap is properly inserted in
the ends of the waist one.
fig. 74 Fasten the ends of the waist belt to the central
buckle.
fig. 75
The waist strap must always pass through the side
rings (S6) and, when being used, it must be adjusted in order
to properly secure the baby.
fig. 76
Always use the crotch strap together with the waist
one, adjusting both of them properly.
WARNING! The inobservance of this precaution may
result in the falling or sliding out of the baby with a
resulting risk of injury.
MAINTENANCE OF THE LINING
It is recommended to remove the lining periodically to
provide for its correct maintenance.
fig. 77
Extract the waist strap from the side rings (S6)
paying attention to let the first teeth of the buckle pass
INSTRUCTIONS
through the side ring before extracting it completely.
fig. 78
unhook all buttons of the lining.
fig. 79
on the lining.
fig. 80
When reassembling the lining, verify that all supports of the
platform (S7) are properly inserted in their suitable openings
under the lining of the same.
WARNING: make sure that the lining has been properly
reassembled before use.
RAIN COVER (IF AVAILABLE)
fig. 81
button up the snap fastners on the side (P1).
fig. 82
front tubes on the front assembly, making sure to fasten the
hooks (P3) under the front platform.
Extract the platform from the supports (S7) and
Then, pass the back straps through the buttonholes
Remove the crotch strap and then the entire lining.
To mount rain cover (R4), place it on the hood and
Then, pass the two rubber bands (P2) around the
31