Dear Customer,
Congratulations on your purchase: the IMER plastering machine
with incorporated horizontal axis mixing machine, resulting from
years of experience, offers maximum reliability and innovative
technical solutions.
- WORKING IN SAFETY.
Before using the machine, carefully read the following
instructions as well as the instructions given in the
attached manuals for the compressor and the Diesel
engine.
This OPERATION AND MAINTENANCE manual must be kept by the
firm s manager at the worksite, and be always available for consultation,
together with the operation and maintenance manuals for the
compressor and the Diesel engine.
The manual should be considered an integral part of the machine
and must be kept for future reference (EN ISO 12100-2) until demolition
of the machine. If lost or damaged, another one can be requested
from the Manufacturer.
The manual contains the EC declaration of conformity (2006-42/EC)
important information on worksite preparation, installation, use,
maintenance and ordering spare parts. In any case, the user must
have adequate experience and knowledge of the machine: the user
must be trained by a person thoroughly familiar with the machine s use
and operating procedures.
To guarantee the operator s safety, safe operation and long life
of the machine, the instructions in this manual must be observed,
together with the current regulations on safety and accident-
prevention at work (use of adequate footwear, clothing, dust
masks, gloves, glasses, etc.).
- Make sure warnings are always legible.
- DO NOT make modifications of any kind to the
metal structure or systems of the plastering machine.
- Always work with the casing closed.
Pay attention when opening the casing: on the inside
there are very hot parts (in particular, engine, compressor,
radiator),
moving
parts
compressor flywheel) and there may be traces of harmful
liquids (in particular, battery acid).
- Check the perfect efficiency of the safety devices,
and in particular the emergency button and the devices
for stopping mixer and agitator in case of opening of the
grill and mixer material door and hopper grill.
IMER INTERNATIONAL declines any liability in case of improper
use, feed defects, lack of maintenance, unauthorised
modifications, and partial or total non-compliance with the
instructions contained in this manual.
1. TECHNICAL DATA
Table 1 gives the technical specifications of the plastering
machine, with reference to figure 1.
2. DESIGN AND CONSTRUCTION STANDARDS
The pumps are designed and built in accordance with the
standards given in table 1.
3. NOISE LEVEL
Table 1 gives the sound pressure levels of the plastering machine
measured at the operator s ear (L
noise level in the environment (power L
to EN ISO 3744 (2000/14/EC).
4. DESCRIPTION OF PLASTERING MACHINE
OPERATION
- The PLASTERING MACHINE is intended for use in
building sites, for mixing and pumping conventional and
premixed plasters and finishing coverings. The premixed
materials must be declared pumpable with these types of
machines by the producer.
4.1 DESCRIPTION OF PLASTERING MACHINE (see Fig. 1)
The main elements of the plastering machine are a hopper
(ref. 1) inside of which there is an agitator (Ref. 2) that
controls an eccentric screw pump (Ref. 3). The mix, prepared
IMER INTERNATIONAL S.p.A.
PLASTERING MACHINE SILENT 300, SILENT 300A
(alternator,
motor
fan,
at 1 m ) and the
pA
) measured according
WA
with the horizontal axis mixing machine (Ref. 4) only provided
for the SILENT300 machine, is poured into the hopper and
pumped by the eccentric screw pump to the sprayer through
the material delivery pipes. Air from the auxiliary piston
compressor incorporated in the machine also reaches the
sprayer and the material is thus sprayed on the wall. The
machine is completed by a supporting casing on wheels
(Ref. 5) incorporating a Diesel engine (Ref. 12), electrical
panel (Ref. 9), pneumatic system, hydraulic system (Ref. 10)
with variable delivery pump.
The machine is supplied with the material delivery pipes and a
sprayer (Fig. 7).
The machine can be fitted with several accessories, and in
particular a vibrating screen (DWG9,PAGE26), a cable remote
control, a radio control, a spray nozzle for finishing surfaces
and grooves and a hydraulically controlled pressure water
cleaner.
The pressure water cleaner enormously facilitates end of day
machine cleaning operations.
The machine can be supplied in the preparation for pumping
self-levelling materials, therefore for use as a pump and not
as a plastering machine. In which case, it is equipped with a
more powerful Diesel engine, an eccentric screw with higher
delivery, and is without an air compressor; the sprayer is not
supplied but the remote control and screen are included
(DWG.11,PAGE29).
The machine can be supplied in the version approved for
towing on roads.
The type-approved towing set-up simplifies machine moving
and placing operations.
5. GENERAL SAFETY INSTRUCTIONS (Fig. 1)
- Before using the plastering machine make sure the
protection devices have not been removed. In particular
check the following safety devices:
- Opening of the mixer grill must stop mixer movement by
means of the device of Ref. 7
- Opening of the mixer material door must stop mixer
movement by means of the device of Ref. 8
- Opening of the agitator grill must stop mixer movement
by means of the device of Ref. 6
The machine does not start if the side impact bar on the
mixing machine side is not correctly fixed in the work
position (Ref. 9).
- Never direct the sprayer towards anyone when the
air and material pipes are connected: if the air hose is
damaged it could cause accidental starting of the
plastering machine.
28