Care And Maintenance - Hilti WSC 7.25-S Manual De Instrucciones

6.4 Sawing along a line
There is a cutting line indicator for straight cuts or bevel
cuts (0° and 45°) at the front section of the base plate of
the power tool. This permits precise cuts to be made at
the selected cutting angle. The edge of the line indicator
corresponds to the inside of the saw blade. There is a
cutting line indicator at the opening for the saw blade at
the front end of the base plate.
1. Secure the workpiece so that it cannot move.
2. Position the workpiece so that the saw blade is free
to move under the workpiece.
3. Check to ensure that the switch on the power tool
is in the off-position.
4. Plug the supply cord into the power outlet.
5. Place the power tool with the base plate on the
workpiece in such a way that the blade still has no
contact with the workpiece.
6. Press the on / off switch.
7. Guide the power tool along the cutting line on the
workpiece at a suitable speed.
6.5 Sawing with the parallel guide (rip fence)
The parallel guide (rip fence) can be used to make accu-
rate cuts along the edge of a workpiece or to cut strips
of equal width.
The parallel guide can be fitted on either side of the base
plate.
6.6 Fitting / adjusting the parallel guide 6
1. Disconnect the supply cord plug from the power
outlet.
2. Slide the rip fence guide under the clamping screw.
3. Set the desired cutting width.
4. Tighten the clamping screw.
6.7 Using the saw on the guide rail 7
NOTE
Using the saw on the guide rail can reduce the risk of
kickback.
6.7.1 Inserting / removing the tool from the guide
rail adapter
1. Remove the rip fence, if one is fitted.

7 Care and maintenance

CAUTION
Ensure that the power tool is disconnected from the
electric supply.
7.1 Care of saw blades
Clean off dirt and dust deposits adhering to the blades
and protect them from corrosion by wiping from time to
time with an oil-soaked rag.
2. Fit the front edge of the base plate into the front
retaining lugs on the guide rail adapter.
3. Swing the rear edge of the base plate down fully
into the guide rail adapter.
The base plate must engage fully with the rear
retaining lug.
4. To remove the tool, pull the rear retaining lug back
slightly and lift the tool up out of the guide rail
adapter.
6.7.2 Longitudinal cuts at 0 °
Place the saw on the guide rail so that the rib fits into the
groove in the adapter.
6.7.3 Longitudinal cuts at up to 56 °
Guide the saw so that the outer edge of the guide rail
adapter runs along the rib on the guide rail. The saw
blade will otherwise come into contact with the guide rail.
6.7.4 Cuts at an angle across the surface of the
workpiece
NOTE
The cutting angle indicated is the angle of deviation from
a straight, right-angled cut.
1. Position the guide rail with the zero mark at the edge
of the workpiece and then pivot the rail until the
desired angle shown on the angle scale is opposite
the zero mark.
2. Use the two screw clamps to secure the guide rail.
6.8 Trimming to size
1. Secure the guide rail from below with two screw
clamps.
NOTE The saw must be placed on the guide rail
behind the workpiece.
2. CAUTION Take care to ensure that the saw blade
is not in contact with the workpiece.
Position the saw on the guide rail a short distance
from the starting point of the cut.
3. Switch the power tool on.
4. Push the saw steadily across the workpiece.
The pendulum guard opens as it contacts the ac-
tuating edge at the side of the guide rail and sub-
sequently closes at the end of the rail as the cut is
completed.
7.2 Care of the power tool
CAUTION
Keep the power tool, especially its grip surfaces,
clean and free from oil and grease. Do not use clean-
ing agents which contain silicone.
en
9