Specifications - Amprobe FG2C-UA Manual De Uso

In-Warranty Repairs and Replacement – All Countries
Please read the warranty statement and check your battery before requesting repair. During the warranty period
any defective test tool can be returned to your Amprobe® Test Tools distributor for an exchange for the same or
like product. Please check the "Where to Buy" section on www.amprobe.com for a list of distributors near you.
Additionally, in the United States and Canada In-Warranty repair and replacement units can also be sent to a
Amprobe® Test Tools Service Center (see address below).
Non-Warranty Repairs and Replacement – US and Canada
Non-warranty repairs in the United States and Canada should be sent to a Amprobe® Test Tools Service Center. Call
Amprobe® Test Tools or inquire at your point of purchase for current repair and replacement rates.
In USA
Amprobe Test Tools
Everett, WA 98203
Tel: 877-AMPROBE (267-7623)
Non-Warranty Repairs and Replacement – Europe
European non-warranty units can be replaced by your Amprobe® Test Tools distributor for a nominal charge.
Please check the "Where to Buy" section on www.amprobe.com for a list of distributors near you.
European Correspondence Address*
Amprobe® Test Tools Europe
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
*(Correspondence only – no repair or replacement available from this address. European customers please contact
your distributor.)

SPECIFICATIONS

1. Main
Frequency Range
Amplitude
Impedance
Attenuator
DC Offset
Duty Cycle Control
LED Display
Range Accuracy
2. Sine Wave
Distortion
1/10 level)
Flatness
3.Triangle Wave
Linear
4. Square Wave
Symmetry
Rise or Fall Time
In Canada
Amprobe Test Tools
Mississauga, ON L4Z 1X9
Tel: 905-890-7600
FG2C-UA
0.3 Hz to 3 MHz (7 Range)
10Vpp (into 50 Ω load) (typ)
50 Ω ±10%
-20dB ±1dB x 2
<-5V to > +5V (into 50Ω load)
80%:20%:80% to 1MHz Continuously Continuously variable
variable
N/A 6 digits; 7.6mm (0.3 in) high
±5% +1 Hz (at 3.0 position)
≤1 %, 0.3 Hz to 200 kHz
35dB below fundamental (typ.) 35dB below fundamental (typ.)
< 0.3dB, 0.3 Hz to 300 kHz
< 0.5dB, 300 kHz to 3 MHz
≥ 98 %, 0.3 Hz to 100 kHz
≥ 95 %, 100 kHz to 3 MHz
± 2%, 0.3 Hz to 100 kHz
≤ 100ns at maximum output.
(into 50 Ω load) (into 50 Ω load)
0.3 Hz to 3 MHz (7 Range)
10Vpp (into 50 Ω load) (typ)
50 Ω ±10%
-20dB ±1dB x 2
<-5V to > +5V (into 50 Ω load)
80%:20%:80% to 1MHz
N/A
≤1 %, 0.3 Hz to 200 kHz
(Specification applied from MAX. to
< 0.3dB, 0.3 Hz to 300 kHz
< 0.5dB, 300 kHz to 3 MHz
≥ 98 %, 0.3 Hz to 100 kHz
≥ 95 %, 100 kHz to 3 MHz
± 2%, 0.3 Hz to 100 kHz
≤ 100ns at maximum output.
10
FG3C-UA