Fault Codes; Locking The Controls - Maytag Magic Chef CPR1100ADW Guia Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

To cancel the Clock display:
If you do not want the time of day to display:
Press and hold the CANCEL and CLOCK pads
for three seconds. The time of day will
disappear from the display
When the clock display is canceled, press
the CLOCK pad to briefly display the time of day.
To restore the Clock display:
Press and hold tile CANCEL and CLOCK pads for three
seconds. The time of day will reappear in the display.
./
--
CLOCK
Timer
The timer can be set from one minute (00:01) up to 99 hours
and 59 minutes (99:59).
The timer can be used independently of any other oven
activity. It can also be set while another oven function is
operating.
The Timer does not control the oven. It only controls a
beeper.
To set the Timer:
1. Press the TIMER pad.
TIMER
• 0:00 lights in the display.
........
• The colon will flash.
3,
Press the A or V pad until the
correct time appears in the display.
• The colon will continue to flash.
Press TIMER pad again or wait four seconds.
° The colon continues flashing and the time begins
counting down.
° The last minute of the timer countdown will be displayed
as seconds.
4. At the end of the set time, one long beep will sound.
To cancel
the Timer:
1. Press and hold the TIMER pad for three seconds.
OR
2. Press the TIMER pad and set the time to 00:00.
Locking the Controls
Tile touch pad controls car/be locked for safety, cleaning, or
to prevent unwanted use. They will not function when locked.
If the oven is currently in use, the controls cannot be locked.
The current time of day will remain in the display when the
controls are locked.
To lock:
Press and hold tile CANCEL and COOK &
/
[
HOLD pads for three seconds.
LOCK flashes in the display.
__
COOK&
HOLD
To unlock:
Press and hold the CANCEL and COOK & HOLD pads for
three seconds.
LOCK disappears from the display.
Fault Codes
BAKE or LOCK may flash rapidly in the display to alert you if
there is an error or a problem. If BAKE or LOCK flash in the
display, press the CANCEL pad. If BAKE or LOCK continue to
flash, disconnect power to the appliance. Wait a few minutes,
and then reconnect power. If the flashing still continues,
disconnect power to the appliance and call an authorized
servicer.
5,
6.
7. When cooking is finished, press CANCEL.
8. Remove food from the oven.
Baking
To set Bake:
1. Press the BAKE pad.
BAKE
• BAKE will flash.
.................
° 000 will light in the display.
A
2. Select the oven temperature. The oven tempera-
ture can be set from 170° to 550°. Press or press
and hold the A or V pads.
• 350 ° will light when either pad is first pressed.
° Press the A pad to increase the temperature.
° Press the V pad to decrease the temperature.
3. Press BAKE pad again or wait four seconds.
° BAKE will stop flashing and light in the display.
• 100° or the actual oven temperature will display. The
temperature will rise in 5° increments until the preset
temperature is reached.
4. Allow the oven to preheat for 8-15 minutes.
° When the set oven temperature is reached, one long
beep will sound.
• To recall the set temperature during preheat, press the
BAKE pad.
Place food in center of oven, allowing a minimum of two
inches between utensil and oven walls.
Check cooking progress at the minimum cooking time.
Cook longer if needed.
%¸¸¸¸¸¸¸¸¸¸;;;¸¸¸¸¸¸¸¸¸¸¸¢¸¸.¸¸¸//
16

Publicidad

Tabla de contenido
loading

Tabla de contenido