Selecting The Direction Of Rotation; Maintenance / Cleaning - Metabo KHA 18 LTX BL 24 Quick Instrucciones De Manejo

Avoid levering with the machine when a chisel
is fitted.
6.4 Setting chisel position
- Insert the chisel.
- Turn the switch button (13) in such a way that it is
between setting
- Turn the chisel to the required position.
- Turn the switch button (13) in position
- Turn the chisel until it engages.
When a chisel is fitted, only operate the
machine in the chiselling operating mode
6.5

Selecting the direction of rotation

Do not activate the direction switch (10) unless
the motor has completely stopped.
Selecting the direction of rotation:
R = Clockwise (for drilling, hammer drilling, chis-
elling, inserting screws)
L = Counter-clockwise (for extracting screws)
0 = Centre position: with the transporting safety
device engaged (switch-on lock)
6.6 Drill chuck change
When changing chucks, make sure that the
spindle is clean. (6) Apply a light coating of
grease to the spindle. (Special grease: Order No.:
6.31800)
Only attach the Metabo chuck provided.
Removing the chuck:
See page 2, fig. C.
- Turn chuck lock (3) as far as it will go (a) in the
direction indicated by the arrow, and remove
chuck (b).
Replacing the chuck:
See page 2, fig. D.
- Place chuck onto spindle (6) (a).
- Turn chuck lock (3) in the direction indicated by
the arrow (b) until chuck slides fully onto the
spindle. Then release the chuck lock.
- Check to see that the chuck is properly seated.
Note: To prevent the spindle from turning while
chucks are being changed, set the switch button
(13) to chiselling mode.
6.7 Tool change with SDS chuck
Before fitting, clean tool shank and apply
special grease (accessories order no.
6.31800)! Use only SDS-Plus tools.
Inserting tools:
- Turn tool and insert until it engages. The tool is
locked automatically.
Removing the tool:
See page 2, fig. A.
- Pull tool lock (4) backwards in direction indicated
by arrow (a) and remove tool (b).
6.8 Tool change with keyless chuck
Use the keyless chuck when non-impact drilling in
metal, wood etc. and driving screws.
and setting .
Tighten the tool (see page 2, fig. B):
Turn sleeve (2) in direction "AUF, RELEASE" (a).
Insert tool as deeply as possible (b) and turn sleeve
in the opposite direction, until any perceptible
mechanical resistance is overcome (c). Caution!
The chuck is not yet fully tightened!
Keep turning the sleeve (it must "click" when
turning) until it cannot be turned any further - only
now is the tool securely clamped.
.
With a soft tool shank, retightening may be required
after a short period of operation.
.
Note: The grating sound that may be heard after the
drill chuck is opened is purely functional; it is
stopped by turning the sleeve in the opposite direc-
tion.
If the chuck is extremely tight: remove the battery
pack from the machine. Hold the drill chuck at the
drill chuck head using an open-end spanner and
turn the sleeve (2) vigorously in the direction
"OPEN, RELEASE".
6.9 Metabo VibraTech (MVT)
For reduced vibrations and less stress on the
hands.
Always apply a moderate amount of pressure to the
handle when pushing down the machine and do not
force. Vibrations are reduced most effectively at the
central position (9).
7. Maintenance, cleaning
- Ventilation slits:
Clean the ventilation slits on the machine occa-
sionally.
- Remove the battery pack periodically and wipe
the contact area of the battery pack and machine
with a dry cloth and remove drilling dust.
- Always keep the spindle (6) clean and apply a
light coating of grease. (Special grease: Order
No.: 6.31800)
- Keyless chuck (1) cleaning:
After prolonged use, hold the chuck vertically, with
the opening facing down, and fully close it and
open it several times. The dust collected falls from
the opening. The application of cleaning spray to
the jaws and jaw openings at regular intervals is
recommended.
f 8. Accessories
Only use original Metabo battery packs and Metabo
accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
Batter chargers: ASC Ultra, ASC 30-36, etc.
Battery packs with different capacities. Only
use battery packs with voltage suitable for your
power tool.
ENGLISH en
7