Set-Up, Operation - Festool PRECISIO CS 50 EBG Manual De Instrucciones Original

CAUTION
The noise emissions during actual use
of the power tool can differ from the
declared values depending on the ways
in which the tool is used especially what
kind of workpiece is processed.
- Identify safety measures to protect
the operator that are based on an estima-
tion of exposure in the actual conditions
of use (taking account of all parts of the
operating cycle such as the times when
the tool is switched off and when it is run-
ning idle in addition to the trigger time).
4.5 Other risks
In spite of compliance with all relevant design
regulations, dangers may still present themselves
when the machine is operated, e.g.:
- Workpiece parts being thrown off,
- Parts of damaged tools being thrown off,
- Noise emissions,
- Wood dust emissions.
5

Set-up, operation

- When unpacking the tool, remove all transport
inserts.
- Ensure that the floor around the machine is
level, in good condition and free of loose objects
(e.g. chips and offcuts).
5.1 Setting up the machine
The machine can be set up with or without un-
folded legs (fig. 1 and 2) (the "Floor" model does
not have foldaway legs).
To unfold the legs, loosen the four rotary knobs
[1-6] all the way. Tighten the four rotary knobs
again once the legs are unfolded.
If the machine wobbles, the length of one leg can
be adjusted by turning the end cap [1-7] until the
machine stands securely.
5.2 Prior to initial operation
5.2a Installing the guard (fig. 12)
- Remove the yellow safety sticker [12-10].
- Set the saw to maximum cutting depth and the
mitre to 0°.
- Pull the wedge [12-8] into the upper position.
- Take hold of the guard and completely unscrew
the screw [12-5].
- Place the guard on the riving knife. In doing this,
guide the lengthwise pin that is located in the
guard into the groove [12-9] on the wedge and
push the screw [12-5] into the hole in the riving
knife and tighten it.
5.2b Installing the preset profile setting rail
Push the handle of the preset profile setting rail
into the zero position (fig. 15). Tighten the screw
[3-6] (fig. 3) and attach it to the table.
5.3 Transport
When transporting the power tool, hold
it by the handle areas on the sides [2-6].
Never take hold of or transport the power
tool by the protective cover.
- Click the saw unit into place in the zero position.
- Remove all attachments from your saw and wind
up the cable on the cable holder.
- Fold up the legs if necessary.
For transport over short distances, two of
5.3a
the machine's leg ends are equipped with trans-
port rollers. Take hold of the power tool by the
handle area [2-6] and pull it to the desired place.
5.4 Scope of application
The machine can be used as a table saw or as a
circular trimming saw.
a) Table saw (fig. 1)
- Set the switch [1-9] to the lower position.
- Swivel the handle [1-8] downwards and use it
to pull the saw unit forwards until it clicks into
place.
The saw unit is now in a central position on the
table and the machine can be used as a table saw.
b) Circular trimming saw (fig. 3)
- Set the switch [3-10] to the upper position.
When the handle [3-9] is swivelled downwards, it
can move the saw unit backwards and forwards for
making cuts. The backwards motion is supported
by a spring force.
5.5 Dust extraction
The PRECISIO has two vacuum connec-
tions: A top guard with bayonet coupling
[2-3] with a diameter of 27 mm and
a bottom guard [2-2] with a diameter of
35 mm.
The CS 70 AB dust extraction set (included in the
delivery of CS 50 EB) connects the two vacuum
connections together so that a Festool mobile
dust extractor can be connected.
5.6 Power supply and operation
The mains voltage must correspond to
the specification on the rating plate.
25