Using The Machine; Refi Lling The Water Tank; Cleaning And Storage; Technical Data - Clatronic DB 3250 Instrucciones De Servicio

Using the Machine

NOTE:
This device should only be used for ironing garments and
textiles!
• Remove any protective fi lms and adhesive labels from the
stainless steel soleplate before using the appliance.
• Completely unwind the line cord.
Ironing without steam (steam jet regulator on „O")
1. Place the iron on its stand.
2. Turn the steam regulator to „O".
3. Always set the temperature control to „0" before connecting
the appliance to a power point, or before disconnecting it.
4. Sort out the garments according to their ironing tempera-
tures. Start with the lower temperatures. It is set with the
thermostat:
„●" Synthetics, silk
„●●" Wool
„●●●" Cotton, linen
MAX
5. Electrical connection
• Make sure that the iron voltage (see name plate) and
the line voltage match.
• Only connect the machine to a properly installed safety
socket, 230 V/50 Hz.
6. The control lamp lights up. As soon as it shuts off, the set
temperature is reached. Now you can start to iron.
7. Always pull the plug out of the socket after using the iron.
Steam Ironing ( )
NOTE:
For this a high temperature is needed (cotton, linen).
The quantity of steam can be regulated using the steam quantity
regulator,
„O"
„ "
„ "
Extra steam can be added with the steam jet function „ ". Turn
the button to the symbol and press it intermittently.
WARNING: The steam is hot. Danger of scalding!
NOTE:
• When ironing at low temperatures, make sure that you
reduce the quantity of steam or iron without steam.
• If the temperature is too low water may leak from the so-
leplate. The appliance features an „anti-leakage function"
which deactivates the steam mode if the temperature
chosen is insuffi cient for steam operation.
05-DB 3250.indd 25 05-DB 3250.indd 25
low temperature
medium temperature
high temperature
maximum temperature
no steam
Small steam volume
Large steam volume
Refi lling the water tank
• Always disconnect the mains plug before refi lling water.
• Set the steam control to „O" (no steam). Open the lid of the
refi ll inlet and carefully pour in the water. Do not exceed the
maximum line as marked on the water reservoir.
Spray Function ( )
In order to moisten a section to be ironed press the spray button.
Turn the button to the symbol and press it intermittently.
Vertical Steam
This can be used to produce a jet of steam in a vertical direction.
Self-Cleaning ( )
1. Half fi ll the water tank with water.
2. Heat the machine up to its maximum temperature. After the
control lamp goes off remove the machine from the mains
supply.
3. Now hold the iron horizontally over a sink. Turn the steam
quantity control to the „
Now rock the device backwards and forwards until the tank
is empty. Reinsert the control, paying attention to the guide
mechanism. Then return the regulator to the „O" position.
4. Place the machine back on its stand and heat it up again. To
clean the base now iron over a clean cotton cloth.

Cleaning and Storage

WARNING:
• The device must never be immersed in water!
• Always remove the mains lead before cleaning!
• Clean the casing with a slightly damp cloth.
• Clean the iron with a slightly humid cloth.
• Always return the steam regulator to the „O" position after
use and empty the water tank in order to prevent any leaks.

Technical Data

Model: .............................................................................. DB 3250
Power supply: ............................................................230 V, 50 Hz
Power consumption: ..........................................................2200 W
Protection class: ........................................................................... Ι
Net weight: ........................................................................1,09 kg
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
" position and pull it out.
25
13.08.2008 11:34:32 Uhr 13.08.2008 11:34:32 Uhr