Functional Description - Milwaukee M18 Manual Del Operador

• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a fire.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is dam-
aged or modified. Damaged or modified batteries
may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
• Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the risk
of fire.
SERVICE
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
CUT OUT TOOL
• Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring. Contact with a
"live" wire will make exposed metal parts of the tool
"live" and shock the operator.
• Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
• Always check the work area for hidden wires
before use. Shut off all live electric circuits to any
areas where cut outs will be made to reduce the risk
of explosion, electric shock and property damage.
• Always use the depth guide to avoid plunging
too deep through the material. Plunging too deeply
could cause contact with electric wiring.
• Check all adjustments are secure before use to
avoid injury.
• Use only cutting bits rated for the speed marked
on the tool. Other types could cause injury, tool
damage, or property damage.
• This tool is not a drill. Do not use with drill or
screwdriver bits.
• Allow the cutting bit to reach full speed before
contacting the workpiece. Contact with the work-
piece during startup can cause the tool to jump.
• Ensure the tool comes to a complete stop before
laying it down. A spinning cutting bit can grab a
surface, causing injury or damage.
• Do not touch the bit immediately after use. It may
be hot and could burn skin.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
• Some dust created by power sanding,
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
UL Listing for Canada and U.S.
C US
SPECIFICATIONS
Cat. No. ..................................................... 2627-20
Volts.............................................................. 18 DC
RPM ..............................................................28,000
Spiral Cutting Bits*.....................1/8" & 1/4" Shanks
Battery Type .................................................M18™
Charger Type................................................M18™
* For use in cutting drywall and multipurpose material.

FUNCTIONAL DESCRIPTION

4
3
2
1
1. Collet nut
2. Depth guide
3. Dust blower
4. LED worklight
5. Spindle lock button
3
6
5
8
9
6. Handle
7. Belt clip
8. ON/OFF switch
9. Depth guide adjustment
button
10. 5/8" Wrench (not shown)
7